Batteries

quote:

Originally posted by yzer

....Running my boat has little effect on DC storage. Underway the engine has a DC generator bolt-on....






Is this something like they had on cars decades ago or something else entirely?
 
quote:

Originally posted by KiDa

quote:

Originally posted by yzer

....Running my boat has little effect on DC storage. Underway the engine has a DC generator bolt-on....






Is this something like they had on cars decades ago or something else entirely?







It's a generator, like cars had before they switched to alternators. I't very easy to rebuild, incidentally.

I have a friend who is a marine engineer. He wants me swap out the generator with one of the new high output alternators but I'm going to stick with the old unit as long as it works.
 
"downsize the fuse/breaker size on your LED circuits?" -- Robyns Nest

Note that a circuit breaker is sized to the wiring; it is not sized by the load. ie: changing to LEDs does not necessarily change the wiring size, therefore, the circuit breaker remains the same.

If you need to protect a specific load, use an inline fuse sized specifically for that load. ( imho, not required in this case ).

-edit-

A more familiar example: Your house is wired for 15A or 20A circuits. You do not change the circuit breaker when you plug in a small lamp vs coffee maker. Note that some items are best if protected at a lower current leven so they come with an internal fuse, such as the power amp on your stereo, or perhaps your wall sized TV.
 
Have to disagree with your assumption. Dealing with AC, yes the wire is sized to the maximum load, not the case with DC. Wire run and load determine the wire size.

LED's draw less amps than incandescent, close to 1/10th the draw. If you do not downsize the fuse/breaker you run the risk of fire. LED's are diodes. Bulbs are like fuses, when the filament breaks so does the circuit. No so with LED's, the circuit can stay connected and if your breaker/fuse is not sized for the load you could have problems with fire.
 
If this bothers you, leave the breaker alone, and add a fuse to the light fixture. I've "cooked off" my share of electronics, and imho, the control electronics for a LED will self-immolate itself long before there is a fire. ( ie: 1/8 or 1/4 watt resistor or current limiter ) And in many cases, there -is- a small, PC board fusible link inside the control electronics. Adding an inline fuse will do little harm. But it is pointless to have a 5A circuit reduced to let's say 0.5A simply because the load is 0.5A. Fuse the circuit correctly. And, if required, separately fuse the load device. Further, I would very likely have far more than one LED light on a circuit breaker. It is much more likely that I would have several devices on that circuit. ie: breakers for circuits that have all Nav Lights or all Cabin lights. You are unlikely to have circuit breakers for each individual LED fixture.

As to the fire risk: keep in mind that a LED fixture will more than likely be rated for less than 10 watts ( some recent LEDS could be slightly higher ). It is very difficult to burn -anything- at less than 10 watts. And if there is greater current, the electronics will fail, ( fried ) open circuit. Every LED I have seem fail has failed open-circuit... ( fried )
 
My personal choice is to not add in-line fuses anywhere in my boat if I can avoid it. The in-line fuses then get buried behind panels, you forget where they are when and if you need to replace, IMHO, something that should be avoiding if possible.
 
Do AGM batteries charge properly from just the alternator on the boat engine? .... Or, do AGMs need to be juiced up periodically from a special charger hooked up to shore power? I do not have shore power or a charger on the boat. Will my alternator do the trick to maintain an AGM battery?
I do have a charger in my garage that has an AGM mode, but I certainly wouldn't want to have to remove the battery from the boat on a regular basis just to charge it.

For more info, when not in use, the boat is dry stored, and the battery switch is "off", so there is no draw.
Thanks.
 
AGMs have no special requirement for charging ( though you may push them a -lot- harder than flooded types ). If you run often enough and long enough to charge a standard flooded battery, then you will charge an AGM just fine. Does this answer your question?

( Obviously, there are always various caveats etc, but they may be used as drop in replacements for flooded )
 
I think all batteries would benefit if a 3 stage charger were to charge them. AGM's charge is similar to conventional wet cells in regards to voltage. If all you are doing is a slight discharge, the boat's engine should do all right. One good thing about AGM's is that they will absorb more charge back into them versus a regular wet cell; meaning it will take less time to get them recharged. The life of an AGM is very similair to wet cells; drain them heavily and the life expectancy will be diminished severely. I've seen top of the line AGM's batteries die in less than 6 months due to heavy discharges.
 
<<....AGMs have no special requirement for charging ( though you may push them a -lot- harder than flooded types ). If you run often enough and long enough to charge a standard flooded battery, then you will charge an AGM just fine. Does this answer your question?"...>>

Yup.

Thanks!
 
Back
Top