best dock Lines

giolic

Active member
exMember
Joined
Sep 25, 2006
RO Number
23638
Messages
1,614
What would be the best lines for a 45 viking ?

2 bow , 2 springs prt & stbd , 2 stern ? What lenghts and size would you suggest for each ?

Mark
 
I'd use 5/8 double braided Nylon for the best feel. 3/4 can also be used if you're really in bad docking positions often. Length is harder to guess without more info about your use & home port docking? Do you stay in on bad storms or Winter Season? No matter what I'd at least have one 100-ft line for an unusual need? You may need more but are you in a slip with fingers, Pilings? Mooring?
 
Mark,

Remember that if you have lines that are longer than the boat on the bow, you run the risk of them finding there way into the water and getting tangled in the props. Same risk with the springs too.

You have 2 spring cleats on your boat so you have options for tying you spring lines. I would go with 35' lines for the springs, 30's for the bow and stern lines.

5/8" braid is plenty for your boat.

Jonathan
 
My personal reasoning for suggesting 50's is because there are times when you may have bow lines strung to the back of the vessel to make docking easier. If 50's were present, one could hand both the bow and stern lines from say the rear of the boat.

The 75's and 100's could be used in the case when towing would be necessary to make a bridal setup.

Doug
 
I am not sure what your Viking weighs but 5/8 sounds a bit thin to me. I have a 50 Navigator and am going to upgrade to 7/8" or 1". I do get a lot of surge in my slip so I want to be on the safe side. Most guides suggest 3/4" for my boat size but with alot of wind and surge I am moving up. If you center tie on your slip you will want 2 spring lines for each side as well as bow and stern lines. I generally leave both forward spring lines on the dock so they can just be looped over the center cleats on the boat when I dock, it makes it much easier to tie up when I return. It is easy to do single handed this way if I need to. As far as length, I like the bow lines close to the overall vessel length, the stern lines half the length and the spring lines about 2/3's the lenght. I sure there are some rules of thumb out there some where.

Hope you enjoy the boat.
 
I believe this is covered in Chapman's, but I don't recall the specifics. Dang my memory is getting bad!
 
My Chapman's is onboard,,, not to worry.

What brand is the best ? Maybe I'll order them from boatfix

Thanks for the feedback all
 
I ordered several lengths of spliced lines from boatfix a couple of months ago. The quality is excellent and the price was great!
 
Couldn't say without seeing the mooring arrangements and knowing more about the boat and expected environmentals, but let me give you this caution:

Assuming you're using double braid nylon (if you're using three strand, slap yourself, then acquire double braid), don't overdo it. The loveliest thing about DBN is it's elasticity. If you use gargantuan lines, or too many of them, all the shockload goes straight to your new (just purchased, yes?) Boat's deck iron, instead of being absorbed by the line. Look at the breaking strengths and WLL's of the line you're using, drop 25 percent for the splice, then multiply by the number of lines. You'll usually find you could (NOT should!) hoist your boat on your alongside lines, when in reality, even the most savage wake will exert only a slight fraction of the boat's displacement on the lines (and cleats or what have you - people neglect the adverse effects of shockloading on cleats and such.

Just a thought for the day for the overkill crowd.
 
Dusty, Thanks for the PM.

Thanks Mike, The Boat came with some 5/8 black DBN lines so I think I'll just pickup a few more.
 
Dock lines rule, leave them at your home dock, the travel lines, have lots of length, but never let them attached when moving. Better to lose a line than pull the rulling gear off.
 
Mike: three strand has more stretch than braid.
 
But a lower working load limit, breaking strength, and sustained loading tends to (don't know the polite word for it) up the lay of the yarns - kind of like a kink or hockle - basically leaving a strand twisted against the lay. Service life is waaaay shorter, and it needs to be tended. DBN lays either way.

Besides, black DBN looks pretty sharp, and doesn't discolor like white.
 
Mike:
hockles are only a problem with the cheap three strand. I have never seen a single hoclke on quality tight lay rope even after I so overstressed them while pulling out a tree that the colored indicator poly strands broke. May be the rope our government buys for the CG is junk from the lowest bidder. You can easily tell the difference by feel and unlaying the rope. Just because it is white and nylon doesent meen it is any good.
 
for travel, 6 50' lines should handle all your needs... 2 bows, 2 springs, 2 sterns. At first glance 50' at the bow seems too long but when you get assigned an extra wide slip and you want to double them up back to the boat to be easy to retrieve the next day, you'll be happy with the 50' lines.

add an extra one for back up...

at your home slip, you have the option of using shorter lines based on your specific needs so 25 footers may work out jsut fine.

mike is right, oversized lines won't stretch and wont absorb shocks as well so this is one case where oversizing isn't necessarily best. If your home slip is exposed and you want heavier lines, you can use those rubber thingys on the lines...
 
Oversized lines can also fill up your cleats more than you want when you need to run two lines to the same cleat.
 
Back
Top