Steering Force Required Question

Crossroads

Member
Joined
Jan 1, 2000
RO Number
2208
Messages
308
I've always owned outboard boats until I bought my latest project. It's a 1978 Mainship 34 Sedan. The boat has an upper and lower helm and has a Seastar hydraulic steering system. The amount of effort required to turn the steering wheel at both helms is about equal but it is considerably stiffer than my old 24 foot Wellcraft with twin 150 outboards. I do not know if the level of effort involved is normal or whether I need to work on something. It doesn't take two hands to steer but it is about as stiff as one hand can do. A 34 foot boat with a single engine and no thruster requires some steering wheel work so I want it right.
 
Pretty normal Bill, since the thrust of the outdrive/engine isn;t helping you to turn, not to mention, you're turning the rudders into the wash of the prop... I know our 340 w/tunnels was extremely hard to steer under power, our 37 Maxum was a little tougher too...our new to us 42 though steers like a charm, but it has a pump to help....
 
On the other hand...My 41 foot single screw steel trawler...with Seastar steering is very easy to steer...and with all the wheel action required when docking...I am glad it is not hard.
I don't have any suggestions...but mine is just fine..so I'm not so sure it should be as hard as your's is.
 
I own several boats currently with Sea Star and can compare them with Hynautics on much larger boats I have owned (18 and 30 tons) The Sea Star (both units are new) is considerably stiffer than the much larger hynautics units. I have a smaller center console, with direct cable steering which is easier than the hydraulic--and only 15 hp less than one of the boats with the hydraulics. So, I would say that stiffness is fairly "normal" with the Sea Star units.
 
Bill- If you have room , perhaps larger diameter wheels could help ease turning effort. You might also try (at the dock) disconnecting the rudder tiller/quadrant from the aft hydraulic line linkage and try turning the wheel. If it is very easy then ,it's possible your rudder port packing is too tight or something else is interfering with relatively free swing of the rudder shaft. Is the SeaStar fill topped-up & well-purged at the upper station?
 
Hello there.
I wonder how many turns lock-to-lock you have in the upper helm?
It could be a bad combination of pump to slave cylinder. If your helm pump is a 5272 and
you have 3 or 4 turns lock to lock I have a 5271 (less displacement) that will give
you 9 turns and much less effort. :)
Cpt. Harold
 
Our previous boat also had 'relativly' stiff steering which was a challenge when docking (one I really didnt appreciate). I added a 'steering wheel knob' and it made a huge difference. With the leverage gained from the knob one handing the wheel was much easier. many marine stores carry them, and a few automotive places still do as well, though I believe theyre probably illegal in cars nowadays. For 30 or 40 bucks, might be worth a try.
Cheers
Terry
 
Bill check your rudder post packing as it might be too tight, also check the linkage on the quadrant to see if it is binding or needs lube. As stated above, a larger wheel will also help.
 
I think Cpt Harold may be on to something. I also think the rudder post packing needs to be redone as I know the drive shaft packing needs attention. Thanks for the help and ideas, you guys gave me some things to work with. In the meantime, one of those suicide knobs on the steering wheel just might help but they don't seem to be very cheap. Working on boats is my hobby, I ocasionally get to use it.
 
I agree with Sandy and The Other Gary, It's most likely a rudder post issue and not just over tightend packing glands. There can be corrosion and junk that makes them stiff to move. As mentioned, the test is to disconnect the rudder arm and see how the wheel turns and if you can budge the rudders independantly. I had this issue on mine 1985 vintage about three years ago.
 
Back
Top