Adding a float switch

interj

Member
exMember
Joined
May 7, 2003
RO Number
11531
Messages
273
This may seem basic to some, but I have a few questions on adding a float switch to a sump pump.

Currently our shower pump is just hard wired, there is a switch in the bathroom we must turn on, the pump runs, water goes out, we turn off the switch and get back to showering. As you can imaging it's a big PITA.

Seems like a good spring project to add a float switch, a few questions:

1. Can all sump pumps take a float switch?
2. Is there additional wiring required?
3. Will the switch still work after the float is added? Will we be required to leave it on at all times?

Thanks!
 
Where does your shower drain to? Where does the water pool before you turn on the pump? All pumps can be wired to a float switch. If you wire the current switch into the system, it will have to be on for the float to activate the pump.
 
1. Can all sump pumps take a float switch? Generally yes.

2. Is there additional wiring required? Yes, from the power source/ground to the switch. This may come from existing wiring or you can run new directly from the power panel (remember to fuse properly).

3. Will the switch still work after the float is added? Will we be required to leave it on at all times? Depends if you wire it that way. There may be instances where you'd need to manually start the pump. If you're using a float switch it may jamb open from debris and you'll need to pump right away. I chose a "Water Witch" solid state switch w/no float so the likelyhood of that happening is nil. I still have the ability to start the pump manually from the helm switch.
 
Greg,

My shower does not drain. I collects in a small well which is then pumped out a through hull with the sump pump sitting in the well.

Rick,

It would seem like adding the float from the existing wireing would be the easier way to go. The show sump has a breaker on my main panel then an on/off switch in the bathroom.

You mention "water witch" switch with no float, I assume this is a non-float, float switch? I will google it.

Thanks !
 
Jeff.....if you wire the float switch to the load side (3 way switch ) ...it should work both ways.

14_A.gif


If you don't have a 3 way switch......you will need to turn on the on/off switch to activate the float switch.
 
Jeff, if you have room in the well to mount a float switch, then it would act just like the shower sump boxes sold by Atwood and others. If you don't have room there for a float switch, adding a shower sump box with it's contained pump and switch would be an easy option.
 
since it's a shower sump, i woudl just add the float switch on the positive wire going to the pump. Leave the switch on for automatic operation or remove the switch altogether... no point in having a sump switch...
 
Pascal,

What would be the harm in wiring it as described in Don's diagram?
 
What I'd do is leave the manual switch off, but wire the two wires from the float switch to the two terminals on the manual switch, so that the float switch and the manual switch are wired parallel to each other. The float switch will operate automatically, but you can bypass it and turn the pump on at any time, by flipping the manual switch to the on position.
 
if the only thing the sump takes care of is the shower, i would not go to the trouble of adding a three way or float switch. the float switch will fowl from time to time with soap and need to be cleaned, the connection for the switch must be made in a way to keep any water from the sump from running down the wire to the connection or it will quickly fail from corrosion. if its a must do, Rule makes a shower sump that has the pump and switch built in to it that you can easily install and wire outside of the sump. it has a built in filter to keep hair out of the pump.
 
The rule "shower pump" is a full well system. I can not install that solution without removing the existing shower and well.

Is this what your refering to?

98aw180.jpg
 
Jeff...... Thats the right way to handle shower water.......it also has a check valve in the exhaust hose .....to keep water from running back down the hose and re-filling the sump.

But you can buy an external check valve and add it to your system.
 
I am not sure how that box would work. Maybe some shower wells have enough room for a 10x8x5 Box?

Here is a picture of our head, our shower sump drains under the white box on the let, it is pumped directly overboard.

1206345_8.jpg


Maybe I need to go with the non-mechanical floats like the Water Witch to avoid fouling. I like the idea of a check valvem, Ill look into that also.
 
quote:

Originally posted by interj

I am not sure how that box would work. Maybe some shower wells have enough room for a 10x8x5 Box?

Here is a picture of our head, our shower sump drains under the white box on the let, it is pumped directly overboard.

Maybe I need to go with the non-mechanical floats like the Water Witch to avoid fouling. I like the idea of a check valvem, Ill look into that also.




I see now. I think folks were picturing a system where you have a hose connected to the shower drain that runs into a remote shower sump box. That's how my system works. The water flows downhill to the shower sump/well and is pumped overboard from there. I have a float switch, but also a wall switch that makes the float switch 'live'. I leave it on all the time, but it only runs when triggered by the accumulation of water in the well. I am lucky that it's easy to access because I like to drop a 1" chlorine tab in the well to keep things from getting funky in there.

Paul
 
Jeff, the sump boxes as above are usually located in the bilge. The showere water runs into the sump and then is pumped overboard from there. I still don't understand exactly what your setup is.
 
Basically, the sump box in the Larson is built into the boat and not removable. I never minded turning it on and off on my 290 but I understand Jeff's point that a float switch would be more convenient.
 
Back
Top