Aluminum Trailers

  • Thread starter Thread starter JZ
  • Start date Start date

JZ

Member
exMember
Joined
Feb 21, 2003
RO Number
11176
Messages
117
Hi, I just started investigating for a new trailer. Anyone have a list of suppliers? I've found 3 or 4, but mostly in Florida.

The boat is 30' and about 10,000 dry. I'm on the West Coast around SoCal, but ideally would take delivery around Tucson, AZ.
 
I just picked up a 2009 Venture that will handle a 29-32' boat with a capacity of 14625lbs including the trailer. They are made in Baltimore, MD, but may have dealers on the west coast.
I will be using the trailer to haul my 1989 Sea Ray 300 Sundancer, also about 10,000 lbs dry.
I would suggest a bunk trailer for a boat that heavy.
 
Thanks, anyone else have any input?
 
I have a Load-Rite aluminum trailer that I'm pleased with. I've also had good luck with E-Z Loader.

Peter
 
I also have Load Rite aluminum. They're made in PA. Not sure if they have them in CA. Got mine at Dave's trailer sales in MD.
 
A lot depends on your use. Although Al offers a lot of unsprung weight, Al in salt water is a nightmare. I disagree with the idea of a bunk if you are looking at any kind of flow to the water or if the ramp does not allow "powering on" to the trailer. More and more marinas are forbidding powering on as it erodes the land under the ramp.

I prefer a galvanized roller bunk for general all around performance. A good power winch block and tackled to the bow will allow you to center and load with no effort from the engines of the boat. Some of the newer winches have a wireless remote that will allow you to single hand a large boat on the trailer.

My 3 cents.
 
There are a lot of them used in saltwater here in S. La.
There is a company in Kenner, La. that manufactures them, but
I cannot remember their name.
 
quote:

Originally posted by KiDa

Al in salt water is a nightmare.






Why is Aluminum in salt water a nightmare? That's why I'm buying an aluminum trailer. For good looks and performance (no corrosion) in salt water.

One of the better one's I've found so far looks like FastLoad in Florida. www.fastloadtrailers.com. If anyone else knows of other good companies please post them.
 
If you want quality to haul your boat don't go with a cheap Aluminum Trailer, as they say you get what you pay for. I went with a trailer from this family in the St. Petersburg FL area. Check out there web site. I will not buy another trailer other than an "Aluminum Slide On"
Owens & Sons Marine Inc.
-Aluminum - Slide On -
Custom Built Trailers
3601 8th Ave. So.
St. Petersburg, FL
33711
(727) 323-1088 or (727) 323-0861
Fax: (727) 323-1517

http://slideon.com/
 
quote:

Originally posted by JZ

quote:

Originally posted by KiDa

Al in salt water is a nightmare.






Why is Aluminum in salt water a nightmare? That's why I'm buying an aluminum trailer. For good looks and performance (no corrosion) in salt water.

One of the better one's I've found so far looks like FastLoad in Florida. www.fastloadtrailers.com. If anyone else knows of other good companies please post them.








Corrosion.
 
quote:

Originally posted by JZ

quote:

Originally posted by KiDa

Al in salt water is a nightmare.






Why is Aluminum in salt water a nightmare? That's why I'm buying an aluminum trailer. For good looks and performance (no corrosion) in salt water.

One of the better one's I've found so far looks like FastLoad in Florida. www.fastloadtrailers.com. If anyone else knows of other good companies please post them.








Corrosion. Al in salt water will corrode. One of the biggest problems with Al is constantly searching for corrosion in the dark corners that are normally seen. The FFG-7 class frigate is a steel hull bonded to an Al superstructure. One of the biggest things we had to be on the look for was corrosion in the superstructure. It is what it is.
 
I have a 2006 fastload tri axle c/w elec over hyd disc's on all axles. Overall I am happy with the trailer. A problem I had was as soon as I got it home (Alberta Canada) I started blowing the brake lines up. The lines they supplied were flexable single flared with brass fittings. The single flare was failing and the hose would come apart from the fitting. Fastload sent me replacement lines and I had the same problem. I talked to their hose supplier and they even sent a complete set of new lines. I didn't think that a single flared line was even legal on brakes but both Fastload and the hose supplier said they were. I even called our Goverment Dept and they told me there was no standard for Alberta (I still question that) I ended up getting a set of flexible stainless steel lines (from frame to axles) and ridged steel for the frame. I have not had any problems since. I was told by the people who supplied the Elec over Hyd unit that the ones for disc brakes run higher psi than the drum setups. I found that the trailer is quit low and for some places I go was a problem . I took the very front and the very back crossmembers and instead of them hanging below the I beam I moved them up to sit on the flange of the I beam. Depending where you go this may or may not be a problem.
 
I've been using my aluminum trailer mostly in saltwater since 2001. I faithfully wash it down, but usually that doesn't take place until the end of the day since it's a trailer boat. Aside from the fact that the outward appearance doesn't look as nice as when it was new, there seems to be no evidence of corrosion. Maybe I can't see it and the trailer is about to collapse, but it seems fine to me.

Peter
 
I wouldn't rule out trailers made of other materials (galvanized), but I would avoid a painted trailer. I trailer our 300 DA each weekend and I've owned bunks and roller trailers. Bunks are easier to maintain due to the smaller number of moving parts. They are also cheaper to manufacture and maintain down the road. Head to any launch ramp and look around and I think you'll see that there are a lot more bunk trailers in the lot. I winch our 300 DA on the trailer and I only winch it about 2 feet. I don't know what could be any easier than that?
 
Aluminum is, in the pure form, highly resistant to corrosion. Aluminum alloys, that is aluminum melted with other metals, can be highly corrosion resistant or very susceptable to corrosion. Obviously, the trailer makers know which to use.

Other metals, particularly steel and steel alloys, when bolted to aluminum alloys can create sites primed for corrosion. Proper bolting and isolating (insulating) techniques are necessary.

Aluminum superstructures and aluminum hulls are common so somebody's got to know how to do it right.
 
There are thousands of alum. trailers on the northern gulf coast that have no corrosion problems.
I have seen them on boats as big as a 36 ft. Fountain with 3 outboards on it.
They are an asset to own, not a problem.
I have never seen any that have a corrosion problem.
 
Aluminum is the only way to go. Make sure the manufacturer uses all stainless hardware. Have had mine for 10 years in salt water and no problems. I take the boat off once a year for boat off maintenance and replace items as necessary. My trailer is Magic-Tilt out of New Orleans, but Champion Trailers out of Slidel, La. makes a good trailer as well.

Aluminum is the way to go. I have had iron, and galvanized, and will never own another one.

babncb
265 Regal
St. Martinville, La.
 
I too bought an Owens and Sons. It was an aluminum, three axle bunk trailer. I used it to haul/stow a 28' Century cuddy. It did a great job. Check with your manufacturer. Some do NOT recommend roller trailers.
 
Aluminum here. Brackish (Chesapeake) and salt (Florida) use. I think that's the only material Float On uses to build trailers, and they're the only company out there that builds one for my boat (and it wasn't cheap).
 
I bought an aluminum trailer specifically because of salt water. It's open channel "I-beam"; easy to hose down. Water is not trapped like in "closed" box section frames. Any corrosion would be easily seen, and not hidden insode a box frame. The aluminim is not kept in the water ike some aluminum outdrives are. No corrosio problems so far on the AL trailer.

.
 
Back
Top