Bottom Paint Touch Up

hock90

Member
Joined
Aug 8, 2006
RO Number
22764
Messages
14
I am getting ready to touch up the original bottom paint on my 2001 Formula 40PC. This boat has been freshwater all of its life and although the bottom paint is 8+ years old, it still looks fair. However, there are some areas where it is obviously getting a little thin. With this said, I am wondering if anyone has any tips on the best (and easiest and cheapest) ways to touch up the entire bottom. I am in an area where bottom jobs go for $40+/ft and can take anywhere from 2-4 weeks to complete; neither of which do I want to endure. I have a trailer for the boat and it is on it and I did a very thurough pressure wash on the bottom. I plan to rough the bottom up with either sandpaper or something like a scotch pad before I paint. Is a "light" rough-up job sufficient? Also, do I need to know what brand paint is on the boat now, or all paints "compatible" (i found some info online that not all paint will stick together)? Any pointers would be helpful--keep in mind that I am unfortunately NOT in a position to have the boat done professionally or sand the entire bottom down to the fiberglass. THANKS!
 
Hmmm. Eight yr old bottom paint is not protecting anything. What you need is a full, fresh bottom paint job.

--

Are all bottom paints compatible? Absolutely not. There are ( at least ) two major types of bottom paints: ablative and "hard". The ablative paint is "built to fall apart". Basically, you apply a multi-coat fairly thick layer of ablative paint, and it softens and wears off ( along with the barnacles ). This type usually lasts from 6 months to a couple of years. It can be "touched up" with the same paint, and very likely, with any other ablative paint.

The "hard" types work differently. Generally they are an epoxy based compound, formulated in a range from "semi ablative" to "hard". They work primarily by a time release of biocides and in some cases, by a mild ablative action. Different formulations most probably are incompatible with anything except the same brand/type.

My info is from memory and subject to inaccuracies. I welcome correction, as required...
 
sorry, i should have stated that it is ablative paint. i understand the ablative vs hard. i found something that suggested that brands/types of ablative paints will not adhere to eachother on touch up applications. true?
 
If you can find out what paint is on there you can get a list of paints that are compatible from any major brand. Then power wash light sand clean and paint it's not as bad as it sounds I repaint mine this year and I had it sanded to the gel.
 
if you plan on keeping the boat on a trailer you will want to use a hard bottom paint as the soft stuff should not be out of the water for more than 24 hours after it is applied. if you can locate the brand that is on there now it would be helpfull. if not select a brand that is available to you and contact that mfg for reccomendations for application and prep.
 
quote:

Originally posted by vic33004

if you plan on keeping the boat on a trailer you will want to use a hard bottom paint as the soft stuff should not be out of the water for more than 24 hours after it is applied. if you can locate the brand that is on there now it would be helpfull. if not select a brand that is available to you and contact that mfg for reccomendations for application and prep.






Interesting. I always thought it was just the opposite. Learn something here every day.
 
Google "supershipbottom" (no quotes) They have a pretty good explanation.
 
Since it's ablative A/F paint and on a trailer, the very thorough pressure-washing you did should be sufficient prep without any sanding. Just tape off the waterline and roll it on, using a bristle brush for spots the roller doesn't cover. Let dry, move the boat a foot or so on the trailer (if all roller) and paint the "vacations" there. or take it to a yard and have it hung in a travellift or temp. put on blocks for easier access. Obviously, keep any surfaces under anodes bare.

Ablative is sooo easy, but even if in fresh water I would think it would be mostly gone in a couple/few years. If you want to extend the time a bit between repainting once again , you'd do well to apply 2 or 3 good coats. Check/follow the recommendations on the label.
 
For a boat that size, go with a multi-season ablative like Mircron Extra with biolux. It's not cheap by any means - usually around $240ish/gallon. For a boat your size with about two coats, you're going to be in the neighborhood of +2 gallons. I would use a scotchbrite pad and rough up the surface, then tack rag it with some acetone before applying the paint.
 
Thanks for all of the suggestions. After a MISERABLE day of trying to prep the bottom, I have realized that I am in over my head!--not an easy thing for me to admit...

I roughed up the bottom with an aggressive scotch brite type sponge. This boat does stay in the water full time, but is pulled on my trailer 1-2 times per year for power washing.

The reason I am rethinking a DIY job is that i found a small area (about 2ftx2ft) of small blisters on the very tip of the port bow. I realize that this needs to be taken care of ASAP. I have a reputable fiberglass guy coming to take a look in the morning to quote me on fixing the blisters and finishing the bottom job. However, in talking with him, he usually just roughs up the bottom as well and paints while on the trailer. My trailer is not great for this job as it is custom for my boat and has 10 different bunks (great for weight distribution) but horrible to paint around.

The long and short is that the guy will probably want to charge 35+ dollars per foot to put the same paint that I have already bought on and have little to no prep as I have taken care of it already.

Are blisters (small blisters--about 2mm each) easy to take care of? I would assume that I should just sand this area extra well to expose blisters (pop them) and paint over it.

Depending on what my guy says tomorrow, it could be a mute point, but any thoughts would be appreciated. Thanks again for everyones input!
 
Back
Top