Computer beep

mmanna

Member
Joined
Apr 29, 2008
RO Number
29973
Messages
46
Hi all,
I have a 86 chris with a 2007 mercruiser MPI 350mag (alpha drive). We have been having some strange issues with it but the dealer has been able to fix everything to date. Anyway a new issue has popped up. The engine starts and runs well but I get a double beep and 60sec pause then another double beep and so on... No problems with the engine (i.e. pressure, temp, volt) and the drive reservoir is full). Do the beeps mean anything other then there is a code in the computer or does the beep relate to an particular code? And is there a reader that a owner can afford. I see the professional reader is $1200... I do plan to run it back to the dealer but at some point I must start to work on it myself and need to find a way to read the codes. I do have an electronic manual for the drive, engine and computer system (which I think is a ECM 555).
Thanks for the help.
 
Deja Vu - I posted an almost identical question a while back.

In the end I had to bring the boat to a marina where they had the right reader. It turned out to be a very inexpensive part (but lots of $$ labor to read the computer and change it).

There are lots of things that "two beep" signal can mean. You need the $$$$ reader to know which one. When I bought the boat, I sprang for a SmartCraft gauge that displays all kinds of engine info, you'd think they'd have included alarm codes. What a scam.

The $1200 might not be a bad investment, where did you see it for that price?

- Tom
 
A single beep in neutral means you are revving the engines to high in neutral, don't know wether you goose both throttles in neutral but thats just one thought. Regards Bill
 
Probably an Idle Air Control Valve(IAC) about a $100.00 fix.
the engine is probably running a little rich, sometimes at idle, sitting at the dock you can see a little sheen on the water, probably not oil, but gas as it is flooding or on the verge of it. The IAC is a DIY job, but you have to have a computer to erase the code.
Good luck.
 
Thanks to all.

I was running at about 1500rpm in neutral (warming up after t/s Hanna). So that may be a possibility but it was a quick double beep. Well it is still under warranty but i am now starting to think i messed up not getting the carb engine. It is a shame it runs great but then again it better since it only has about 9 hrs on it... I just did a google search for the readers part number 91-823686A2 (sterndrive.com has it for $1170). I was also thinking about getting the SmartCraft gauge but assumed it also gave diagnostic info, so thanks for that you saved me some money but you are right at $110 per hour it will not take too many uses to cover the $1200.
 
If these are gas motors the beep is caused by over revving in neutral, mine come on above 1320RPMs. My System View 5000 panels told me what the alarms were.
 
quote:

Originally posted by mmanna

Thanks to all.

I just did a google search for the readers part number 91-823686A2 (sterndrive.com has it for $1170). I was also thinking about getting the SmartCraft gauge but assumed it also gave diagnostic info, so thanks for that you saved me some money but you are right at $110 per hour it will not take too many uses to cover the $1200.






Isn't the Merc DDT actually made by Rinda Industries???? If so, I think you can find/buy it for less than $1200. http://www.rinda.com/marine/marine.htm
 
quote:

Isn't the Merc DDT actually made by Rinda Industries????





Yep, I was hoping for a PC software version. I will look into it more. I hope you all are correct that it was a high idle rev. I will not know until this weekend.

thanks to all
 
I believe the pc version comes from Rinda to. Very nice people to talk to. I just called them on the phone.
 
Back
Top