dive works

PortHoleDiver

Member
exMember
Joined
Sep 5, 2007
RO Number
28496
Messages
50
Needing to have the zincs changed and bottom scrubbed. Dive Works of kemah, anyone got the number, or who have you used and happy with??? Also, who do you recommend to wash wax compound the boat? Also who would you recommend to install the drippless packing system to my inboards???
 
if you are changing up to a dripless packing system i would not try this with the boat in the water.
 
Before changing to a dripless packing system make sure your shafts are in very good shape or it may not be worth it. I had bought a set of shaft seals to put on my boat. I had to have the bottom done and had a boatyard do them for me. First of all they said the ones I had (PSS Shaft Seal Packless Sealing System ) would not fit the boat too long and so I had to use a different brand. I said ok and returned the PSS ones. After the yard put on the new ones they leaked and they had to pull the boat twice to fix them. They said your shafts are pitted too much and we need to send them out for machine work. Long story but I asked them why didn't they tell me this to beging with and just replace the packing? Well we thought you were set on having dripless seals. Will not be using that boatyard ever again too bad really because they did do a nice job on the other work and bottom job. I just think they were a little to greedy.
 
I spent a lot of time researching dripless seals but re-packed with GFO instead. Bilge has been dry ever since and I haven't thought about dripless seals anymore. That job you can do with the boat in the water.
 
I decided to go with the drippless seals due to the assesability of the packing. I have a 300 sedan bridge, SeaRay. they don't give you any room to work. Last mechanic was about 90 lbs and 5'6. me I'm 6' 230. I can't fit to get under the engine. All I can see is a stream coming from the packing nut. Have had these done three times in two years and bildge is always wet. I will check with the yards when I have it hauled and make sure they check the shafts. When you had to have your shafts smoothed what did that run you? Just looking for the best place to have this done in the clearlake texas area. Also, someone mentioned to get a crossover hose installed also.This I plan on doing. Hopefully pss will work for me. I really don't know what price to expect for labor, or what would be reasonable. I have 1.5" shafts and I believe the componets are 250.00 per engine. Installation?????? Anyone got any ideas??
 
PHD I'd bet something is wrong that can be repaired correctly. (I'm not saying anthing about dripless seals because I have no experience with them)

In the 50's and 60's I had three boats with shaft drives. These were Wooden boats and mostly open to the rain. They were always wet in the bilge anyway. Hey, just whats wrong with a wet bilge?

Fortunately for me I could walk right around to the shaft logs and work on them pretty easy.

One developed a leak that was more than a leak. I kept messing with it for a few months and finally pulled the nuts off and discovered the packing was in there in three pieces. Some dilbert....etc!

I got some of the Graphite packing (this is a long story) and slowly and carefully fed it into the packing gland with no twists or wrinkles.
If your gonna do this yourself, you should plan on getting the correct size and plenty more than you think you might need.

I had to tighten the Nut a few more times after the installation because the wearing in process seemed to allow more water to slip by after each usage for awhile.
After awhile I had it adjusted to where it would drip once a minute.

I can see you thinking that all what I just said is well and good if you can get to the Packing gland nut easily.

Unless that part of a shaft boat has changed drastically since my old boats, I'd bet it has to be done the same way.

Get a light, and a good mirror, and a Packing gland wrench ( I made my own) and keep it right down there with the mirror where it will always be handy and plan on standing on your head after each run for awhile until you get that one drip per minute.
 
quote:

Originally posted by PortHoleDiver

I decided to go with the drippless seals due to the assesability of the packing. I have a 300 sedan bridge, SeaRay. they don't give you any room to work. Last mechanic was about 90 lbs and 5'6. me I'm 6' 230. I can't fit to get under the engine. All I can see is a stream coming from the packing nut. Have had these done three times in two years and bildge is always wet. I will check with the yards when I have it hauled and make sure they check the shafts. When you had to have your shafts smoothed what did that run you? Just looking for the best place to have this done in the clearlake texas area. Also, someone mentioned to get a crossover hose installed also.This I plan on doing. Hopefully pss will work for me. I really don't know what price to expect for labor, or what would be reasonable. I have 1.5" shafts and I believe the componets are 250.00 per engine. Installation?????? Anyone got any ideas??




Diver, be sure that the stream is truly coming from your packing gland. On my da340 I thought I had a bad gland 'cause there was always a stream of water from that area, but I couldn't actually even see the shaft.. When I got in where I could see the water was actually coming srom nmy water heater where the heat exchanger hose nipples had corroded off. So I replaced the water heater instead and the glands still don't leak excessively. That was three years ago.
 
Diver,

If the leaking is related to the dripless seals it could be one or more more of several things. It could be the water source hose connection, or it could be the surrounding hose or it could be the lip seals. It could also be related to prop shafts being out of round.

Last year I had my shafts checked and replaced the lip seals. A complete replacement of the whole seal system is about $350 in parts. Lips seals were around $50. Having the shafts checked cost $90 each; one needed truing and that added another $60.

I keep my boat in Clear Lake. Who do you plan to have do the work ?

To your original question, in my opinion the best dive service in the area is from Sunshine Yacht Service. Check your PM.
 
Thanks folks for the input. Thudpucker, Thanks for the info, but I can see the packing nut but with the design of the boat even a packing nut wrench doesn't work. I had to cut the handle off a pipe wrench to get in there and then you can't turn it but a quarter inch at a time. Am at the point I just want to pay to have dripless installed and forget about it, except for mirror inspection after/before a run as in the regular prestartup inspection. Thanks for the input on checking the shafts. I will have the mechanics do this before installation and also have the props checked.
 
Back
Top