Docking a single sterndrive

89SeaRay220

Member
exMember
Joined
Jun 21, 2006
RO Number
21903
Messages
151
Hey all!

The weather was perfect tonight for some docking practice. Hardly any boats are in my marina so far. I take this opportunity to practice my docking. I've gotten very good at docking when heading toward the slip, with the slip on the starboard side. I made it my goal this year to get good at docking heading toward the slip with it on my port side. I tried it tonight and it was a mess. It's alot harder to see the slip, since the helm is on the starboard side. I got quite frustrated tonight.

The boat is a 22' single sterndrive small express cruiser.

Any tips on docking approaching the dock with it on my port side?

Thanks,
Dan
 
Approach at about a 40 degree angle...slow...real slow...toggle the throttle in and out of gear to maintain forward motion...as the bow closes into the dock go to reverse while turning the wheel to port (into the dock) which will swing bow to starboard...go to neutral and come along side dock finger.

Like anything else...it takes practice. The key here is - Go Very Slow! - Have your first mate on the fore deck with a line ready.
 
Pick a spot along the pier where you want the boat to stop.

Make your approach toward that spot from far enough out that the boat is settled, and tracking straight, on a steady course.

When reversing to stop, no matter what, shift into neutral when headway stops.

A big fender should be close at hand.
 
been a while since i've docked a stern drive IO... 8 years or so, a wide beam 25 express.

basically what mike said... approach and use the stern drive in reverse to swing the stern in and the bow away. I do not agree about having someone on the bow for a couple of reasons... first there little to grab on there, except the bow rail with is often too low on small boats... so if you throw it into reverse a little too fast, it coupld be splash time :-)

also, the bow of a boat is always the worst place to jump on the dock from since they have to climb over the rail. not a huge deal on a small express but as you get into bigger boats it's downright dangerous and you may as well do it right : have you crew step on the dock from the stern. I've seen people falling overboard at the bow, it's not pretty.

i'm not sure i understand the visibility issue you are mentioning.

what you must always remember is which way your stern drive is turned towards because this is going to have a huge effect on any gear/throttle imput. I often see people putting the boat in reverse with the wheel turned away from the dock, either becasue they came in that way, turning, or because it's the natural thing to do to "avoid" the dock. big mistake : that obviously kicks the bow into the dock and the stern way which is the opposite of what you want.
 
Always put it in nuetral before turning your wheel, once the drive is in the position you want, then put it in gear but not before. Too often people shift and then begin turning the wheel not realizing that brief moment in gear with the wheel wrong can be the difference between a good docking and a not so good one.

If you can dock stbd. side to then you already know what to do, just start practicing portside to.
 
I run a line from the bow back to the stern .. make the approach as described above. When the stern is close enough to either hand the lines to a dock hand, or have someone step onto the dock (note do not jump!, they now can control the bow and stern no matter what the wind and current are doing.
 
I prefer to dock to port because that is the side I find easiest to board and debark. And remember with a single I/O, the prop will usually tend to pull the boat to port when in reverse. Always approach the dock into the wind/current, if applicable.

I go against the current at a 45* angle toward the dock until my bow is just about touching. Then I do a short quick forward burst with the wheel hard to stbd. Then while in neutral, I crank the wheel hard to port and gently put it into reverse. If I'm lucky, that brings the back quarter of the boat to the dock on port. I can then step off the boat to the dock and secure the boat by myself.
 
Some of each! The end result is to have my boat at the dock with the port side resting against the dock. This is not for pulling into a slip.
 
quote:

Always approach the dock into the wind/current, if applicable.





Actually, lying stern-to-wind gives more control. Stop the boat stern-to-wind, tuck the stern in to the pier, hitch the stern line, let the boat settle, hitch the other lines and fenders, and go have a cold one.
 
boathandler.....all professional instruction I've been given was not as you say. However, different boats handle conditions differently. Are you referring to a stern only tie up? This discussion began as a side-to alongside a dock.
 
what mike and Psacal said... " basically what mike said... approach and use the stern drive in reverse to swing the stern in and the bow away."
Using reverse as the final move is the KEY and don't be afraid to give it SOME throttle because you don't get as much bite in reverse. When you get good it's kind of a one shot deal and your done. You approach the dock at an angel going from forward to neutral slowly whenever possible and as the bow comes very close to the dock you will have already turned your , when in neutral , wheel the opposite direction so that when you put in reverse the stern will move toward the dock and you seem to almost move sideways into the dock. But start slow and add throttle when needed. Watch others … the last move is somewhat fast.

Do a google search for uspowerboating docking
 
Actually, lying stern-to-wind gives more control. Stop the boat stern-to-wind, tuck the stern in to the pier, hitch the stern line, let the boat settle, hitch the other lines and fenders, and go have a cold one."

Nr 1 sign someone is a true amateur : setting their fenders AFTER they dock.

explains the comment about how a big square mass (stern) is more controlable into the current or wind than a streamlined shape (bow). getting the stern in first is how you paralel park a car, not how you dock a boat...
 
Different boats do handle differently, but often a boat is higher in the bow, and will be more controllable with the stern into the wind. Also with an outdrive or outboard you can back wherever you want to go and the bow has no choice but to follow. With the bow into the wind you're performing a balancing act.

You have to learn to do it BOTH ways; there may not always be a choice.

Stern to the wind is NOT a good idea in rough weather though!
 
Lots of good advice. They key to backing in a single stern drive is to know where the boats center of rotation is. This will tell you when to reverse and bring the stern around to line things up.
 
quote:

Originally posted by Flutterby

boathandler.....all professional instruction I've been given was not as you say.





Unfortunately, the boat and wind don't care what the instructors say…adhering, instead, to the laws of physics.

Per "Start Powerboating Right" the self-described "national standard for quality on-the-water instruction" p. 42:

"Because the bow wants to turn downwind, it is usually easier to hold the stern into the wind, provided waves don't come over the transom."

The qualifier "usually" recognizes that the statement is true for most, but not all, types of powerboats.
 
quote:

Originally posted by PascalG

Nr 1 sign someone is a true amateur : setting their fenders AFTER they dock.





Not after, during. The fender must be available to be placed where the boat first touches the pier, to absorb initial contact. Previously-rigged fenders may or may not do that, depending upon the skill of the person at the helm.
 
DURING ?

oh that's great advice... yeah.. right... I'm going to leave the helm and set my fenders while docking ! or have crew running around he deck rigging fenders... i prefer to set them BEFORE approaching the dock... i use 4 to 6 fenders on my boat when docking alongside, depending on conditions, they are guaranteed to be where they need to be.

obviously I'm talking docks and bulkheads here... if you have wooden pilings you don't need fenders unless you're captain crash..

so, let me get this right... picture a long east/west dock with boats tied on the north side and a 15kt breeze from the east. dock is fixed, no pilings, there is a 70' gap for me to dock. you're suggesting coming stern to the wind, docking on port side, and try to force the bow against the wind towards the dock ? you're saying that's easier than coming bow into the wind (remember, wind alongside the dock) and letting the wind push the bow towards the dock and slowing the boat ?

right...

and if your students attempt that with inboards, i hope they remember that as they use reverse to slow the boat down (remember the wind is pushing the boat all that windage at the stern) they no longer have rudders to control the boat.
 
quote:

getting the stern in first is how you paralel park a car, not how you dock a boat...





Clarification: With wind blowing along the pier, bow-to-wind is how YOU dock your flush-deck Hatteras; stern-to-wind is how I dock my Regulator 26 (singlehanded). Your way works for you on your boat; my way works for me on my boat.

Let's let Dan with the 22' Sea Ray decide for himself.
 
ok, so once again, don't make broad statements about having more control stern to the wind. It is misleading... i'd hate to be downwind from a guy trying to dock even a 35 express stern to the wind... maybe it works on a small outboard powered boat, but it's a receipe for disaster with anything larger...
 
Back
Top