Docking twin I/O's

JeffR

Member
exMember
Joined
Dec 7, 2005
RO Number
19718
Messages
277
I didn't want to hi-jack the other thread going on regarding docking but it got me thinking. We purchased a new-to-us boat this past winter, and will be making the maiden voyage home with it in a couple weeks. My previous boat was a single I/O and I was pretty confident docking. The new one is twin I/O's, and while I'm not really nervous (yet) about it, I'm not sure what's correct, either.

Since it's I/O's, can/should I still use the drives to steer me when docking like you normally would with the single I/O, or should I treat it as an inboard and keep the drives straight and use only throttle/shifter control?
 
I've seen it done both ways by two different drivers and both are good at their particular method. I guess a lot would depend on the beam wind. The biggest difference I have seen with twin I/O's left straight is the amount of throttle necessary to swing the bow around due to the closeness of the props as compared to an inboard.
 
I went through the same transition. At first, I used the steering wheel 'cause that's what I was used to. After trying to not use the wheel and only the shifters, docking was much easier.

Of course, in a pinch, I would swing the drives one way or the other if it helped...for instance when docking paralell as opposed to backing in (bow up to dock, swing drives and hit reverse). When backing in, pivoting, etc, shifters only with occaisional throttle.
 
When we went from our 25 foot single V8 to our 30 foot twin V8 I/O, I had the same thoughts. ex.Use the throttles only, use the steering wheel or sometimes a combination of both.

I think it best to practice and be comfortable with each method.

When I dock at our home marina, the water is sometimes around 4' deep with a silty bottom. You stir this up real quick using just throttles to stern in. I like to use the steering wheel in this case to stern in so I don't have my engines sucking that silt up as much.I kick the bow out with the steering wheel then just reverse right into our well.

If I'm working at getting into a well in a tight marina I will likely only use my throttles to dock as I feel I have better control this way in tight quarters.

I do also use a combination of both steering wheel and throttles depending on the circumstancee.

Mike.
 
WE also learned the hard way.
Many times I'll only use one motor, leave the other in idle, depending on the wind direction.
It is very difficult to spin a boat with these drives, can be done but takes a LOT of practice.
AboutTime
 
I used to dock a 23 foot Thunderbird (think Formula) that had counter rotating 170 HP Volvo Penta I/O's. The counter rotation offered a modest advantage if conditions were calm. But the props were so close together it was marginal. Without much practice I used to dock and manuver the boat on just one engine leaving the other one out of gear. That boat handled just like a single I/O using just one engine. The advantage of the twin was redundancy and speed. That little boat was a screamer with unbelievable acceleration.
 
I docked my twin I/O mostly without using the wheel, just like an inboard. As long as you got good power on your engines you'll be fine. My Volvo 5.7's had plenty of bite and shifted very smoothly so it was very easy to handle in a similar way to an inboard. Even rotating the bow into the wind was not a big deal.

However, once in a while when I was already sliding into the slip and needed to 'kick' the stern sideways I'd use the wheel for a quick adjustment... Sort of like you'd use the rudder on an inboard.

Of course parallel docking was different and I used the wheel for that since it's so easy!
 
No wheel just drives. Works great at all stern in docking. Parallel docking is tricky depending on wind. Remember you always want to dock into the wind if possible. Wind is your friend if you know how to use it. Before docking I always look for some sign of wind direction. I don't worry much about the current.
 
I learned on my twin I/O. I would think that for the delivery home you'll want to do it the way you know how already. No sense in practicing then. But when you have some time and space, try practicing with just the throttles. I think with time you'll find this to be much more effective. I have significantly more manuverability, particulary in reverse, than my sigle engine friends.
 
I dock with just the throttles but use the wheel and throttles for close quarters manuevering when still making headway. Once I hit reverse it's pretty much just the throttles.

Really works just great to bump the boat around. You'll learn how your boat reacts pretty qickly. All the options make for a lot of control. Bump starboard in reverse pulls aft starboard, bump port forward moves bow starboard, etc, etc.
 
quote:

Originally posted by interj

I dock with just the throttles but use the wheel and throttles for close quarters manuevering when still making headway. Once I hit reverse it's pretty much just the throttles.

Really works just great to bump the boat around. You'll learn how your boat reacts pretty qickly. All the options make for a lot of control. Bump starboard in reverse pulls aft starboard, bump port forward moves bow starboard, etc, etc.




I like the 'grocery cart' visual. Just pretend with the shifters (throttle/shifter) that you're pushing the grocery cart. The kind with the rear wheels that pivot are even more like a boat.

Paul
 
this might be a good form to bring up this idea. has anyone other that me thought the i/o's might work like a poor mans ips drive if you put a hydraulic cylinder in the linkage that conects the drives. basicly you would flip a switch when you wanted to go to docking mode the cylinder would actuate causing the right drive to go full right and the left drive full left. you would then have no steering however the drives would be pointing aginst each other and I would think that walking sideways or close manuvering would be much better.??? any ideas??
 
I know about the axius, but that requires either a new boat or a significant amount of money to repower and reconfigure. I was thinking of something more in the reach of the rest of us. say a modification that would use existing hydraulics like the trim and tilt pump of power stering pump. and a cylinder that would replace the current link. I would think someone could do the system for say $500. and not the 10 to 20K ( I'm guessing) to repower with a axius system if they offer it as a package for older boats.
 
Thanks everybody for the advice and suggestions. It sounds like either will work or is doable, depending on the situation. I guess my best bet is just to get some time behind the wheel and see how she responds to different inputs and techniques.
 
I'll add one thought that you may find useful as to being able to walk your twin I/O sideways using both the wheel and the shifters.

Fully turn your wheel toward the dock (or whatever you're trying to move away from), pull the starboard into reverse at the same time you put the port into forward. You can do the same on inboards of course, but it works much better on twin I/O's. In calm conditions your boat will go almost perfectly sideways.

Outside that, just use the shifters and leave the wheel centered. Otherwise you may forget where your drives are centered and cause yourself problems. Put a piece of tape on the top or bottom center of your wheel when the drives are straight and you won't have to worry about that either.
 
quote:

Originally posted by sbw1

I used to dock a 23 foot Thunderbird (think Formula) that had counter rotating 170 HP Volvo Penta I/O's. The counter rotation offered a modest advantage if conditions were calm. But the props were so close together it was marginal. Without much practice I used to dock and manuver the boat on just one engine leaving the other one out of gear. That boat handled just like a single I/O using just one engine. The advantage of the twin was redundancy and speed. That little boat was a screamer with unbelievable acceleration.




I had a Formula 233 I found turning the drives to right, right in reverse and port in forward the boat would walk right over to the dock.
72Formula233cockpit.jpg
 
Keep your trim tabs [if you have them] all the way up. It seems to handle better when backing in.
 
Back
Top