Dripless stuffing box

PortHoleDiver

Member
exMember
Joined
Sep 5, 2007
RO Number
28496
Messages
50
Has anyone installed the dripless stuffing system? The one that is water jacketed, PSS shaft seal. Am really considering haveing these installed as it is nearly impossible to reach my stuffing boxes and am tired of having any water in the forward bildge.
 
You will NOT be sorry. They work very well. Consider a crossover when installed. In the event you ding a prop and have to shut down one engine, it precludes the need to run the engine on the bad prop burning fuel needlessly while limping home.
 
No such thing as a box you stuff that does not drip.....

Walter
 
David, so I understand.... Run the cross over to allow water to come from the running engine and around shaft of the non-running engine right? This is to keep system on non running engine cool when prop would be moving ,in opposite direction, due to movement through the water and in neutral right?
 
What happens when the water supply tube fails either running or at dock, bilge pump can't keep up or battery dies.
 
quote:

Originally posted by kole

What happens when the water supply tube fails either running or at dock, bilge pump can't keep up or battery dies.




Its just not that much volume of water
If the bilge pump can't keep up with the amount of water that would come out of the hose - you need a bigger pump
If you don't have enough Juice to run the pump while running you have much bigger problems then the small leak of the hose and if at the dock the shore power/chargeer will keep the pump going
 
I put one in three years ago and I really like it. I've got a Chesapeake deadrise, so I'm not the fastest boat around. I hardly ever get above 4000 rpm, so with 2:1 reduction shaft spins about 2000. My PSS does have water injection to prevent a vacuum on shaft seal bellows at higher speeds. The injection is run from heat exchanger drain. I'd expect many other hoses to blow before the low pressure injection hose would.
 
I have the PSS system on my boat. They work great and are standard equipment on many boats.
 
We upgraded to the PSS system when doing the refit.

Works great, no problems whatsoever.

I was told however that if we needed to run on one engine that it would be necessary to keep the dead engine's prop from freewheeling with a pipewrench or a large vicegrips. We have never tried this, perhaps we should before we have to.

I'd like to hear more about ths crossover system.

RWS
 
If you're limping home at hull speed on one engine, water injection to the PSS isn't really required. The question is whether your transmission gets enough lubrication. My plain old Velvet Drive manual states that free wheeling is OK.
 
Yeah, locking the shaft is for the tranny, not the dripless, but the crossover keeps both dripless seals cool when one engine is shut down.

-Michael
 
quote:

Originally posted by PortHoleDiver

David, so I understand.... Run the cross over to allow water to come from the running engine and around shaft of the non-running engine right? This is to keep system on non running engine cool when prop would be moving ,in opposite direction, due to movement through the water and in neutral right?






Correct.

The other option is to vice grip the shaft to a stop. I know folks that idle along on one engine when not in a hurry, to the crossover does well in their situation. Not something I want to try, but they do it.
 
Porthole,
You may want to look at SureSeal dripless. Whats cool about this setup is you can put a spare seal on the shaft, so in the future if you need to replace the seal, you won't need to haul the boat. See the video in the link below.

http://www.tidesmarine.com/
 
we simply upgraded the stuffing in our old school bronze "box" to a teflon impregnated goretex material. snugged it down and it barely drips - i m convinced that we get more bilge water from condensation on strainers and thruhull pickups than we get from the stuffing boxes. plus the bilge pumps always belch back water so a completely dry bilge seems almost impossible unless you vac it out or hook up a diaphram pump.

we are going on 3 seasons on our stuffing boxes - they take maybe a 1/2 crank a season to keep things dry
 
Gfo packing is an easier, cheaper option for a dry bilge.
 
Back
Top