DSC radios

Kp,
thanx.. im with the program now ...

Raymarine states something isnt wired correctly .. It should indeed ask if i want to plot the positon request.

Thanks for the info guys

Rob
 
Ok so the plot thickens ...

The raymarine E 120 only has a single nema input. My heading sensor for my radar overlay is plugged into it ... So as it is configured from the factory the DSC radio NEMA output is not connect to the GPS ... There for no DSC distress or call can currently be plotted.. I have to pick either or... They make a duplexer to handle two NEMA inputs but raymarine does not think it will work properly... to be continued....

Rob
 
I think that you need an E55059 ( http://www.raymarine.com/raymarine/ProductDetail.asp?site=1&section=2&page=1011&product_id=3113 ). Search Boatfix, they have them. This will work if you have a E or C Series chartplotter. It is not clear to me if this will work with other plotters. If you have multiple E- series displays, you can split the inputs between the displays. You could wire the heading sensor to one display and the DSC radio to another display. The data would then be shared by all units on the network.

Your certified installer will get this figured out. work with him.
 
MArk,
Thats what we did ... split between the two displays...

Only thing now is when a position request is sent its leaving off the seconds...

but all works now .... way to much work...

Also sending a distress isnt just pushing a button. so if u have a dial channel selector u have to scroll tru menu's after u hit the distress button. select what emergency ... then the message.. way to many steps when stuff could be going bad... IMHO...and people i dont realize there are steps .. I think they just figured pushing the distress button was all they had to do when in fact pushing the button only opens a distress menu ....
Rob
 
Hey Rob,
On mine, the "nature of distress" menu is optional. Maybe yours will work the same way? If I push and hold the distress button, it will count down 5-4-3-2-1 and then issue a distress call. If I push and release, I get a menu. Of course, I've never actually tried the push-and-hold, but that's what the book says.
 
Joe, Mine reads like a novel... The manual didnt say a word about holding the distress button. Just activation and following the menu selections .. Hopefull will never have to use it but atleast i got the plot features working ... The ray 24o is pretty easy to use.. my buddy has another raymarine with the knob to change channels ... holy cow what a pain in the butt to program it.. cant imagine how bad in case of distress his will be to operate...

Rob
 
My Standard-Horizon is much easier to use!
 
I like the idea of calling an individual with a position. This would be great for 4th of July raft-ups where someone always arrives after dark (can you see my flashlight?). Also there are large gatherings like the Air and Sea Fleet Week or the Columbus Day Regatta that are difficult to find friends in a crowded anchorage. Unfortunately, NONE of my friends that I would be looking for have a DSC radio. My current radio works well so I'm not likely to change it even though it has no DSC capabilities. Dropping the seconds on a position report would annoy me.

Have you experienced large number of distress calls on your DSC radio. I read an article about "relay storms" where distress calls were being repeated. The article was a bit dated but I don't know anyone that has a fully capable DSC radio.
 
DeeRow,

I have received too many general calls via DSC than I can remember. During my time at sea going from the U.S. East Coast to India and back, we would receive somewhere around 5-6 per day (except for in the middle of the Atlantic). These were mostly received on the MF/HF band, although occasionally one would come in on VHF. The MF/HF ones were relays and the vessel calling was usually well over 500 miles away. We also got a fair share of actual distress calls, always a relay and again usually a few hundred miles away. Getting such calls is so routine that you almost stop reading them.
 
GMDSS consoles have that annoying 'binger' for DSC gc/ac's - enough to drive you nuts....
 
quote:

Originally posted by November Charlie

GMDSS consoles have that annoying 'binger' for DSC gc/ac's - enough to drive you nuts....






haha, yes - yes they do. Especially when it's on the other side of the bridge and doesn't like to shut up, ever after you press the button 500 times.
 
Need some help. Has anyone used the position request feature? The radio receives the the full location info but leaves off the seconds when it sends it to the chart plotter....

Any thoughts ?

Rob
 
quote:

Originally posted by Robski97

Need some help. Has anyone used the position request feature? The radio receives the the full location info but leaves off the seconds when it sends it to the chart plotter....

Any thoughts ?

Rob






What is the make and model of the sending GPS and radio, and the receiving radio and GPS? Seems to me that the problem could originate in any one of 4 units. It could be a communication setting between GPS and radio (NMEA 0183 or 2000, baud rate, etc). Or it could be a software bug. Call the manufacturer. Furuno NavNet GPS has a port monitor that will display the message on screen. You could use this to determine which unit is responsible for dropping the seconds. Either the radio is not sending, or the GPS is not receiving it.

If you have a laptop with a serial port, you can wire the radio or GPS to a serial cable and read the data using hyperterm.

Good luck!
 
Back
Top