Engine will not turn over??

as JD said, starter is probably buried under the back of the engine. it's that bad to get at if you have decent access...

you must have the right socket and driver... not the $19.95 cheap china 200 piece set :-) space limits the amount of space you have to turn so a power tool makes a bg difference... I used to have a bayliner 25 years ago and used a cordless driver to pull the starter .. had to do it a couple of times over the years, made a big difference...

hopefully you wont' have to pull it.

for a 2 year old boat, thats a lot of corrosion and rust on top of the engine, lots of spray, where is that coming from ?
 
I decided I want this done right so I called a pro. He can get to my boat Thursday or Friday.

Pascal, the corrosion is not from spray, but from stinking rain water. Sometimes when the sunpad / engine hatch cover gets saturated and depending on the way the boat is sitting on the trailer water drips onto the engine. I'd like to be able to get to the boat after every thunderstorm to wipe her down, but just not possible this time of year.
 
Maybe you should cover the boat with a large tarp when it is sitting in the rain.........corrosion can be the death of an engine.
 
Point made about the access on I/O engines in the thread on outboard vs inboard on a 22 foot boat! Agree, the starter on the 350 is very difficult to access.

Look at the engine ground--this is often a connection which is overlooked and is very often the major point of corrosion. You do have a lot of corrosion on the engine. I would not only consider a cockpit cover (slant back or trap) as well as spraying the engine with corrosion block every few weeks. I do this after each heavy run. It will keep the engine and connections much better.

Agree you have to take the connections apart and clean them, then put on a material for preservation of the connection to prevent further corrosion.

Another point is that in I/O's if the gears are damaged in the lower unit, the engine may not turn--this is not hydrolock or a broken engine, but the shifter in these engines is in the lower unit. If a tooth or two gets broken and jams in the correct place, the entire system is locked up. You tain't going to turn over a starter, if the engine will not turn.
 
my IO experience is only limited to an earlier volvo but the tranny was in the upper unit,
not the lower unit as in an outboard. damage in the lower unit woudl not affect the engine ability
to crank or run at idle. I thought all IO where like that, but knowing how Merc's are always different....
maybe they are.
 
Pascal,

All outdrives make two 90* gear turns.

Alpha and earlier merc drives have positively anemic gears. It still amazes me that they even hold up as well as they do. It doesn't take much to crack/break those gears either. A few shifts with the engine reving a little too high or shift too quickly from reverse to forward(or visa-versa) without letting the RPM returning to idle is all it takes to set up the gears to fail. The gears will go, sometimes without excessive load as when accelerating. Just normal running...and boiiiiinnnnnnng.
 
My I/O experience has only been with Mercs, and all had the shifters in the lower unit. Don't know about volvos. Some engines have jack shafts, and transmissions behind them, but a marine transmission is a fairly good size unit, and many I/O's try and get the engine as far aft as possiable. (which leads to the problems accessing the starter.
 
I have never had an I/o before,but I have had a similar problem. Do I/o's have a neutral cut out switch? On an inboard engine, it looks like a 1 1/4 inch bolt going into the side of the transmission that has 2 wires screwed to it. If the switch goes bad it does what you are describing. if you disconnect the 2 wires and twist them together it by-passes the switch and will start. Lokk for 2 wires coming from the area you circled going to a silver greenish looking bolt on the transmission or outdrive.

Hope this helps!
 
charlie, bob,

interesting... Ive never had and will never buy a merc io !! :-)

the volvos (at least the earlier 280 and DP drives) are very simple.
the gear is in the uppper unit. takes about 5 minutes to remove and you can do
that leaving the drive on the boat (intermediate housing and lower unit)

and of course they have a proper water pump on the engine and good seals in the bellhousing to
prevent water leaking in the bellow from sinking the boat !

just a well designed drive... dont' know if the current models still are
 
Yup! Volvos are made the way they're supposed to be made. The way Bravos are now made.

They all have to make those two right hand turns so there are gears at each of those junctions.
 
Problem resolved!

The bad news is it was not as simple as the slave solenoid or a weak battery. The good news is it had nothing to do with the engine being hydrolocked or the transmission.

The mechanic (by the way if any one needs an honest, experienced marine mechanic who will come to you in S. FL at a very reasonable rate, let me know) did some of the trouble shooting as described in some of the responses above and in 10 minutes concluded it was the starter. Thank goodness I called a pro, my body does not do the things this guy had to do to replace that starter. Once replaced, she fired right up.

By the way, the mechanic said that when he used to work on coast guard boats, many of them had a similar problem with rain water leaking onto the engine. He told me of a simple solution which is
a PVC pipe cut through the middle to create a gutter. We will be doing that soon.
 
Back
Top