Fender Flat

rommer

Active member
Member
Joined
Oct 5, 2003
RO Number
12280
Messages
6,037
I have 6 fairly new 10" x 26" center hole fenders that tend to need re-filling with air on a regular basis. I have one home for the winter since I'm making new covers for them and I determined that the leak on this one is the fill valve itself.

It is the same type of valve like you have on a basketball, uses the needle inflater to fill it.

Is there any secret to getting the valve to close properly after you inflate it? Are the valves replaceable?

Would hate to replace the fenders after only 2 years at $50+ a pop!
 
Unscrew the valve and wash it in water then spray wd 40 into the valve then work the air pin in and out and replace.
Taylor has an excelent warranty if that doesent work.
 
The fenders I have do not have anything to unscrew, just a rubber needle valve like a football or basketball. A little concerned that the WD40 might eat the rubber but then again they are leaking now!

This is the type of fender I use

bigb.jpg
 
I heard Taylor Made has a lifetime guarantee on fenders. I have no idea if this is true or not. Either way, call the manufacturer, maybe they'll be helpful.
 
Taking off on Walshie's comment, I know a friend punched a hole in a fender snagging it on a cleat horn. Took it back to a commonly known marine ground store and immediately got a free new one...
 
If they are Taylors they will give you new ones if the valves are bad. If you punch a hole in them you might not get them replaced. Worst Marine has been clamping down on replacing holed fenders in my area.

Jonathan
 
I went and read Taylors warranty and it it does specifically state that the warranty covers air loss problems only due to "splitting or bursting"

Still worth a visit to West thou. I wonder if I'm not inserting the inflation needle correctly if all 6 have leaky valves. I always thought you just wet the needle and push it in but sounds like I should be using some kind of silicone based lubricate instead of spit?
 
I had one I was about to throw away, cause I pumped it up with a basketball pump several times and the air leaked out, I was suspicious of the valve though cause you could hear it coming out of there when filled to the max. Anyways, I spit on the pump's needle valve and worked it in and out of the hole a bunch of times until the valve finally closed. Hey it's worth a shot......
 
Inflate the fender then submerge and see where the leak is. if it is the valve try the wd40. if the leak is elsewhere, without a cut, taylor will probably replace it.
 
I've burst a few large Taylormade fenders and had more than a few leak. They'll replace them.
 
FWIW - I decided to email Taylor Made to ask about warranty coverage of the valves and with in a few hours I received a very nice email back asking me for my address so they could send replacement valves right out. I have no idea how they get replaced but I'm sure they will have instructions.

Anyway just wanted to point out when a company does the right thing... Nice job so far Taylor!
 
I forgot to add, I tired a little WD40 on one of the fenders but it doesn't seem to be helping...

On another note the fender cover I made from boat blanket came out really nice!

IMG_1038.JPG


IMG_1039.JPG
 
Hey John,

They are going to send you the new screw in valves, won't work on your fenders.

Nice job on the covers.

Taking orders????

Jonathan
 
She described them as the "little black rubber ones" but who knows.

Thanks for the compliment. No orders accepted at this time but you never know!

It just one of those, I want to see if I can do it myself sort of things. Purchased a few books about canvas making and I've been playing.

So far not as hard as I thought.
 
John, maybe you can make Pete and Butch new thongs!
 
If all else failed I think I'd try some tire stop-leak...
 
Try putting a small dab of Super Lube on the inflation needle, then work it in and out several times. Repeat two or three times. If that doesn't fix it, nothing will (providing that it's leaking from the inflation nipple).
 
I received confirmation email today which I'm posting below:

"I will be sending those replacement valves out to you this morning. The best way to inflate them is to make sure the needle has some kind of vaseline on it so it goes into the valves easily.

To replace the valves, just use needle nose pliers to remover the old valves from the fenders, put a little vaseline on the new valves and push them right into the fender.

I hope this solves the leaking problem."

I still give them an A for effort on this one but until I see the valves come out with a pair of needle nose I'm not 100% convinced this will work.
 
Back
Top