First Boat, Crying for HELP!!

NO GIN

Member
exMember
Joined
May 29, 2009
RO Number
31320
Messages
349
Hey guys! New to the forum and boating. I recently purchased a 1987 Thompson Daytona 290 with twin 3.7 mercs and Alpha I drives. Bought her from the original owner who was a boat mechanic and maintained the boat very well.

...and the story goes....

When I first inspected the boat both motors ran very well with the only thing needing attention was the shift cable on the port side. Going into forward the boat shut down.

I rebuilt the original helm with all new Faria gauges and re-ran some new wiring that was old and worn. With this I removed everything including old gauges, wiring, switches and remote controls.

... on and on and on and on .....

Now after the helm is back together I can't get the port engine to turn over (cranks fine), and I had coolant shoot from the exhaust port out the transom. I did a pressure check which revealed a loose hose, loose bolt allowing coolant to seep out and the heat exchange drain plug loose. Tightened everything up, drained the coolant and replaced with new. Pressure goes from 15 LBS to 12 LBS in 2 minutes time then slowly drops from there. The starboard engine will not engage in reverse and PSI drops from 15 to 13 slowly and remains there.

I beg of all of you to please help my sorry a**.

Thanks for reading and helping!

Joe
 
..... didn't get one. :( - first mistake of many, stupid, I know!!
 
I'm no mechanic but wouldn't a drop in coolant pressure be normal as the engine gets to operating temp and the thermostat opens?

Ditto on Les's surveyor question. Did you have it surveyed?
 
I did the pressure check without the engine running. Engine was cool and still dropped pressure. NO SURVEY.
 
"Bought her from the original owner who was a boat mechanic and maintained the boat very well."

????
 
Yeah John. I think that in my haste of tearing apart the helm and removing shift cables and remote controls I may have messed things up. I also noticed after attempting to run my port motor several times a kink in my hose leading to the muffs not allowing water into the drive. That may have caused some damage.
 
Some advice and guidance would be much appreciated here guys. I took the day to work on her and try to figure this mess out.
 
NO GIN...no disrespect intended, but couldn't you go back to the original owner (mechanic) and seek some advice from him? Not sure if there are any boat mechanics/engine techs by trade on this forum, but certainly many have done extensive work on various parts of their boats and can offer some help. Possibly post some of the engine/mechanical issues in the engines, electrical, plumbing forum where you may get better results.
 
I tried that John and the original owner retired from boating and his job and moved from NY to Tennessee and will not answer my emails or calls.
 
First I'd check that there is power to the coils that comes from the ignition switch through the kill switch and then back to the motors.

Are you getting water in the oil? My first guess would be a blown head gasket.
 
depending on how long the drive was run without water getting to it, it's possible the impeller is toast and needs to be replaced.
 
How are you doing the coolant pressure test? Gauge on the pressure cap?

The only way I know to lose pressure in a closed cooling system is through the heat exchanger, head gasket, or possibly the blocking plate on the riser. Any could be at fault. You need to rule out each. The fact it won't fire may mean something as a coolant leak by itself would not cause any issues in the cylinders themselves, but of course a head gasket failure sure would.

Why don't you do a compression check and see whether you get any smoking guns there. Not to mention, pull the plugs and turn the engine over and see if you get any antifreeze out of the cylinders. If you have antifreeze in the exhaust it came from the cylinders, seeping into the raw water (which I doubt you would notice), or coming directly through a failed riser blocking plate.

In any scenario I think you need to redact the statement "maintained the boat very well". Don't worry about being embarassed, you are hardly alone. Most of the guys pointing it out have some direct experience in the subject. I was there once. Which is why in a few months you will be joining us in the chorus of "Did you get a survey", followed by "from a good surveyor, not the one the seller provided". Oh wait....you havn't gotten to the second part of that phrase yet!

Good luck, there is a lot of info here. I'm sure we can all help work it out.
 
Where in NY are you? Please tell me that this isn't the Boat that was up around Sacandaga Lake....????
 
Sorry to hear you purchased a lemon from a 'mechanic' who has no interest in responding to you. Personally, I'd do the same. He is done with it, now it's your problem. You know nothing, and could follow up with thousands of questions.

With that said; you have a B.O.A.T - Bring Over Another Thousand.

The coolant pressure will increase until the t-stat opens and drops the coolant temp, although yours seems high. You say it continues to drop - how low? How did all the stuff get loose? 1/2 or full FWC? How are the manifolds? Do you have a merc manual? Did you wire the ignition 'on' correctly? Are you getting a spark? Are you getting fuel?

Engage the F/R and the engine shuts down? Your on the hard or trailer? Problem could be huge, or simple. Did you wire the start in gear protection correctly? Maybe the outdrives are full of water and rusted.

Swabby9009...more info on the boat you think he has....
 
You have so many problems I don't know where to start.
 
New fuel pump, filters and lines I put in. Fuel delivery to the carb is great as I see it squirt in both sides of the carb.

Checked spark by pulling a plug, attached it to the wire and cranked the motor. Saw the spark at the plug tip.

Ran a jumper cable from the + battery to the + coil and she cranked. Did it again and she cranked again. Did it a third time and nothing.

When I shift into reverse and forward the Shaft Roller Switch moves off center.

Removed end cap from heat exchanger and bid pressure test from the pressure cap. Noticed a small amount of fluid coming from one of the lower tubes. When I removed the heat exchanger drain plug the seawater looked like Mountain Dew.
 
I am on blocks at my house still waiting to go my my mooring in Mt. Sinai harbor.
 
Back
Top