Fitting new canvas...

JeffreyCooper

Member
Joined
Mar 17, 2002
RO Number
7889
Messages
36
Hey Folks!

Well, I got my brand new canvas from Cruisers. It looks fantastic!!! Only trouble I'm going to have is that NO snaps were installed (which makes perfect sense). I did get a box of 1000 snaps (the snap kind) and some thru-hole-types for the little blade-type snaps that push-thru and then you twist the end... and I DO have crimper pliers for your "typical" snaps.

So, my questions are:

a) What's the best way to get these snaps located correctly for a nice snug fit? Obviously, the "male" part of the snaps are already in place.

b) What's the best way to poke holes through my new canvas for the new snaps that I can crimp with my handy pliers.. Like a leather punch or something?

c) How do the through-hole snaps get installed? I think there are only four of them, but they would require a bigger hole thru canvas and vinyl window material, then the two pieces (both sides) some together and are crimped... is there a special tool, or do I just bend the tabs by hand?

I'm betting someone here can keep me from butchering my new canvas.

Any and all advice is welcome!!!
 
They make an attachment that fits the male side of the snap with a pin sticking out. You put these on the snaps and then overlay the canvas and where the pins put holes in the cnavas is where you mount the corresponding female side of the snap.
 
Hm - thanks! I guess I'm wondering what the most cleaver way would be to cut the holes in the canvas/vinyl without making a mess, causing frays, tears and other costly booboo's. :-)

I think I can zip it all up, let it get nice and soft in the bright warm sun, then pull it tight and mark where the snaps should go, but any tricks on where to start would be appreciated!
 
You can use a snap fastener tool, which will run you about $5.00 or the best way is a pressn snap tool - when I did mine a local sailmaker loaned me theirs.
 
Jeff, my snap tool [looks like pliers] punches the hole and installs the snap. I've installed scorse of snaps on everything from my top, side curtains, drapes to clothing. Practice on a fabric scrap, measure twice, mark once, check it again and set the snaps. On our side curtains I had my wife stand a few feet behind me to view the whole panel to make sure I wasn't pulling the curtain askew.
 
Coolness - I see a gadget that looks like Vise-grips called "Pres-n-snap tool" (with six dies!)...Is that what you borrowed In The Know?

The snap-tool I have looks more like pliers (cheap pliers)... I don't know if it pokes the hole for me or not, but I've replaced dozens of snaps with it (with the hole already there). I've never done one for these oval-shaped eyelet one. I wonder if Home Depot or Lowe's can hook me up, or if I should just be patient and order the above vise-grip?

I keep telling myself "...Patience..."
:-)
 
Jeff:

The one I borrowed did not look like vice grips, but more like a regular pair of pliars (like Charlie describes). Probably the same tool as this was a few years ago that I did this.
 
Jeff, go to the local fabric shop and buy a remnant and try out your tool. I understand your fear. I retired from owning a cabinet shop.Once I paid $400 for a piece of Purpleheart [exotic wood] that had an amazing quilted patern on it.It nearly caused a divorce because we were very poor at the time. I waited 20 years before I found just the right project for it. It's now part of a desk and credenza top in my wife's study. I made the pieces with a mariners compass of cherry, birdseye maple and the purpleheart. Even used the purpleheart scraps for door and drawer pulls. There was quite a pucker factor involved;)

If you aren't comfortable with doing it after some practice, pay the canvas guy. From personal experience I can tell you that eventually you;ll have to repair the canvas anyway. Sooner or later wind wins! Then you'll know how to repair it.
 
Jeff

If you are that concerned about making a mistake with your brand new canvas [I would be too!], why not
just hire a pro to do it for you? Someone who has the proper tools and experience to do it right the
first time?
 
Jeff:

That is it. Agree with Charlie - pick up some scrap and practice you do not want to have to go through a steep learning curve on your new canvas.
 
Liz, that totally defeats the spirit most of us guys aspire to. You must understand that Tim, the tool man ,
Taylor is something of god and role model to us. If the gadget had a motor it would be even better.
Aghroo ooh ooh... more power.
 
Thanks for a good laugh!!! I guess it is a "guy thing"!
PrettyLady.gif
 
Dear Jeffrey

I just bought a cockpit cover from Great Lakes Co. and I have the same situation. Lots of canvas and no snaps installed. I did not think much about the snaps until I started to study the project and then I realized that I was not ready to start poking holes into $800 worth of canvas when it was something I had never done before. I visited a local canvas shop this morning and a worker is meeting me at my boat on Monday evening and he is installing all the snaps for $100, sounds like a deal to me. I'll let you know how it turns out.
 
Thanks to all who have posted - I might get the guts to try this myself - I think I need to zip it all in and see how hard it's going to be... I'll keep you posted!!
 
Allow for some shrinkage. If you let it heat up and stretch it real tight before marking your snaps in 6 months it will have shrunk enough that if you ever take the top/windows out, you'll never get the snaps back on.

Don't ask how I know.
 
Back
Top