Fuel Cross-Feed System

Pilotpak

Member
exMember
Joined
Feb 18, 2007
RO Number
25250
Messages
185
Hi,

I've got a 310 Larson, with two petrol Mercruisers that run in a tank-to-engine fuel configuration.

But my generator only draws from the port side tank, and as we run the genny a lot, we quickly get a substantial fuel imbalance, (list is exaggerated as both tanks are located outboard).

I want to install a simple gravity fed cross-feed, i.e. a line joining both tanks with a cock that could be open to allow the tanks to equalise.

Has anyone done this ? Any considerations re the type of cock to use ? I'm wondering if the resistance of the tank strainers may prevent gravity feeding ?

Wayne
2006 Larson 310 Cabrio
 
This is actually done every day, vertially every over the road truck ( 18 wheeler ) has an equalization line running between them. If you could route it in a safe manner, away from any heat source, keeping it fairly level and below the tanks, it should work fine. I would put some method of turning it off. I do not personally see any reason this would not work. Other opinions may vary however.........D.........
 
or instead of a cross feed, you could just add a pickup to the second tank (shoudl be available from the builder) and just put a selector valve so that you can feed the genny from either tank.

soudns like a better solution to me...

my previous boat was a 37' express with tanks outboard of the engine and also the genny pulling from one tank... even though we used the genny a lot it was never enough to cause a list.
 
Better check up on this first. In this country it is against CG regs tohave a gravity feed line.
Al
 
Why not run both tanks to a manifold, then you can switch which tank the genny runs off of.
 
Yep, gravity equalization line is bad mojo. One, if the line breaks, you can't stop the flow of fuel, two if a tank become comtaminated, you just contaminated both thanks. Manifold and/or selector is a better solution.
 
Thats how my 37 Sundancer is set up.......2 fuel tanks....1 selector switch ( port/starboard/both ).....feeds both motors and gen set.
 
mine is a little different a pump allows transfer either way so it serves the same purpose but also allows transfer for other reasons.
 
Thanks Guys,

BTW,..Approached local Merc dealer to do this work yesterday and they won't do it. They are not prepared to install any components in the fuel system that is not manufactorer's equipment or an option. Insurance issue I guess.

Larson don't provide any X-Feed or manifold options, so I'm stuck with a lop-sided boat !

Wayne
 
You just need to find a more flexable mechanic..( read: side job )
 
check if your stbd tank has an extra pick up, like the port tank. if so, order a fuel pick up from the builder (the dip tube, and the integrated non syphon valve at the top) and install it.

get some marine fuel line, an appropriately sized 3 way valve and install it. it's all non pressure being on the suction side, it's a 30 minute job...
 
You can easily convert your system, I am in the process of working on mine now. A good starting point is at your water separating remote filters. It could look something like this...

  • line in from tank one to filter 1 with shut-off
  • line out of filter one with tee for engine/gen, then shut-off then tee for engine 2 then into filter 2
  • line in from tank two to filter 2 with shut-off
This will allow you to run on tank 1, 2 or both.
 
Thanks,

I did think about the "T" at the filter idea originally, but I didn't know if it would cause a problem.......

i.e. There's an anti-syphon valve on both tanks... there's also a small fuel pump on the generator. I'm worried that if the genny is running while the main engine is stopped, that the smaller amount of suction provided by the genny may not be enough to break-open the anti-syphon valve, but may try and suck fuel backwards thru the main engine's fuel injector pump. ???
 
It may suck fuel out of the line and pump but I doubt it. Even if it did when you turn the main engin ingintion on and the pump spools up it will easily load the line in a second or 2.
 
Bayrat,

I'm no expert on this, but I just drew up the system you're working on. I think there's a danger that you might suck air into your engines.

Tank.jpg


Say you elect to run both engines from Tank 1. There'll be a lot of suction applied to your cross-feed line, which inturn is connected to your gen. If suction is applied to your genny's fuel line is there not a chance that it could syphon fuel out of the carburetor's fuel bowl and you may suck some air into your main engines ?

Wayne
 
Have you taken into account that in many (all?) of today's injected engines fuel is not only taken from the fuel tanks, escess fuel is also returned there. You want to insure that any hookup you make provides for return lines. You do not want to be using fuel from one tank and returning the excess to the other tank that may aleady be near capacity.

G
 
why would you have one side of the Xfeed connected before the primary and the other after ?

also, when the Xfeed valve is open, you have both a main and the genset pulling from the same line, not ideal , i'd worry about the main preventing enough fuel from getting to the genny.

as i said before, check if you have an extra pick up port and install a new fuel pickup.
 
Pascal,

That is not exactly how mine is, the cross feed is made with the filter heads. In addition, I do not have return lines so that isn't an issue in my case.
 
Back
Top