Fuel flow meter

JAYROCK

Member
Joined
Sep 18, 2007
RO Number
28607
Messages
272
How do these gauges hook up? Is there a sender at the fuel line and a wire to the gauge?
Thanks JAYROCK
 
Basically, yes. Sender/transducer in the line with wires going to a dedicated guage. Some are "stand alone" units and some are add-ons to other marine electronics.
 
For a gas engine with no return line, there is a single turbine type of transducer which is put in line with the fuel input, after a course filter. These include the Northstar (Navman), Lowrance, and FloScan. There are a second type where there is a return line for diesel or gasoline. This reqires a second transducer which measures and subtracts the fuel returned to the tank.

A third type--either engine specific--such as Yahama or Honda sell, or Lowrance which is NMEA 2000 and hooks up directly to the engine--and these use the engine's injection computer flow measurements.

These all require 12 volt power and the NMEA 2000 the NMEA 2000 "backbone"--with its guage.

All are quite accurate and worth having in these days of expensive fuel. The savings in fuel by running the boat trimmed properly to give the best fuel economy will pay for the guage in a year or two.
 
Thanks for the replies, I am looking at the North Star F210.It seemed to have nice features for the $$$.I think it will allow me to fine tune my cruise speed and range.I hand fig a 80 mile trip in calm waters and it avg. 2.1 mpg ( Maxum 2500 scr w/5.7 bravo 3 22pitch with a full load ) I didnt think that was to bad?.?....
 
I have the flow meter made by FloScan. I have two sending units (one for each motor) that are plumbed into the fuel lines right before the fuel pump. The wires from the sending units go directly to the gauge on the dash.
 
We have the same setup with a floscan twinscan. Installed myself. The hardest part was installing the sending units because of how difficult it was to get to the fuel lines. Our tanks total 210 gallons. We have had up to 155 gallons filled with a two gallon variance between what floscan calculated and what was actually pumped. Usually we have around 100 to 105 filled and it is always dead on.
 
I was looking at the Northstar unit , as far as i can see they only have a single engine model. If a person is only concerned with total GPH and total used could a person use this on a twin engine boat . I can't remember but I think that I have one fuel outlet fron the tank that splits to both engines . If my boat is setup this way I thought that I would be able to put the sender before the split to the twins.
 
Northstar hooks directly to Mercury Smartcraft engines, so that is high on my list. I like the Lowrance backbone setup as opposed to the black box method.
 
Jay-
You are pretty close on at 2.1 mpg. I had a 1990 22ft. Dancer w/5.7 & Alpha One, got about 2.1- 2.2. this 25 ft. Dancer gets 1.8, w/BII
 
I have two new Faria's. The starboard one seems to register ok and the Port one has to be sent back over the winter to be checked. It is registering consumption of 1/3 that of the Starboard engine.

Anyone else?
 
I installed Lorance on my Searay. They work great and are very accurate. They were also about 1/2 the price of the Floscan. Also, my digital meter was only 2" in diameter, so it fit nicely in the dash.
 
Les:

What is it that you know about these instruments and have not told me?
 
The Flowscans were great in my 454's.

Absolutely accurate.

I have not installed any in my diesels, as I have been told that they have myriad sensor problems, especially with contamination issues.

Plus with return lines, we'd need to have 4 sensors to deal with.

Anyone else using these with diesels ?

RWS
 
quote:

Originally posted by RWS

The Flowscans were great in my 454's.

Absolutely accurate.

I have not installed any in my diesels, as I have been told that they have myriad sensor problems, especially with contamination issues.

Plus with return lines, we'd need to have 4 sensors to deal with.

Anyone else using these with diesels ?

RWS





I installed a basic flowscan (can't remember the model # but it has analog fuel flow and digital totalizer) on my 120 horse cummins/mercruiser this past spring. 110 hours later I'm very happy with it's accuracy and felt no need to calibrate it with the dip switches.

I have found that likely due to the negligible fuel flow, it doesn't register any fuel consumption on the totalizer at idle to fast idle.

Installation was relatively simple and I have not had to touch the system since. It has been a great investment for my application and operating environment.

As far as the sensors becoming contaminated is concerned, they should be installed downstream of an adequate primary filtration system (a single Racor with 20 micron element in my case). If the sensors are becoming contaminated, I shudder to think what's getting to the secondary filter and/or the engine.

Kev
 
quote:

Originally posted by C team

I have the flow meter made by FloScan. I have two sending units (one for each motor) that are plumbed into the fuel lines right before the fuel pump. The wires from the sending units go directly to the gauge on the dash.





Doese the one guage give you seperate GPH info or combined info for bolth motors?
 
Thanks Kevin.

The problem with my application is that the design utilized the flow of diesel fuel with a high rate of return volume to aid in keeping the injector pump cool.

Even with the 10 micron Racor 900's (we had to use the 900's due to the volume) I am still concerned about sensor failures down the road.

I'd sure like to hear more about flowscans in similar situations.

THANKS !

RWS
 
Hi RWS

I suggest you check out Floscan's website. They have a model # vs engine model selector that should be able to help you out. You should also be able to contact their tech department if you have any questions about your installation. Then of course talk to Les when you're ready to buy.

Good luck.

Kev
 
Back
Top