Help putting canvas on!

kmont97

Member
Joined
Jan 1, 2000
RO Number
2289
Messages
33
I tried putting the sunbrella canvas and iesenglass on my walkaround today. Unfortunately the snaps don't line up right. I know its on right but it seems to have shrunk! I've snapped where I could I guess I'm just hoping that the sun will stretch it out. Any other advice???
 
Soak it in cold water and then install. Let it dry while all snapped up.

Hope you didn't wash it in warm or hot water!
 
Whern i was in NH i saw windows shrink up as much as 4" lenbhtwise on some windows. let it warm up. actually try snapp the fartherest snap first then fill in the middle.
 
There's also a tool made that gives you more leverage and makes it easier to push the snap on. If you google "top snapper" you'll find it. I checked to see if Boatfix has them but I didn't see it.
 
Cold canvas and vinyl panels definitely shrink. Either use one of those snap tools or wait until the panels warm up a bit in the sun.
 
Try This

www.ironwoodpacific.com/products/boat_tools/topsnapper.htm

Les posted it here a year or so ago, it works well.

Sandy
 
Back when I had the kind of enclosure I would take down & put back up, I installed 2 sets of snaps at key places. One for cold and one for when the clears warmed back up and stretched back out. No more over stretching and breaking snaps.
 
You could also try using Extend-A-Snap. They come in packages of 4. We often use them on our canvas when we can't stretch it enough.
 
I start the zippers, but leave them unzipped until after I have gotten the canvas snapped. That gives me some play and it is easier to zip closed with the added strain then to snap. Also try a warm day or wait until the wrmth of the afternoon instead of the cold in the morning time.
 
Thanks all for the advice. I finally got all the snaps!!! Now its the zippers which attach the side panels to the front panels that are the PITA.
 
We cut off the shrink wrap Friday and put ours on, it was around 55, we were close to inch short in most places. I let it go till Saturday when the temps got up to around 70 and the problem went away. Heat!

Niles
 
I would be very careful if you have to pull on your canvas that much to get things to fit...Wait for warmer weather...If you have to pull that much you are putting a lot of stress on sewn parts...If it doesn't fit in the warmer weather I would go with BJL's idea of the Extend-A-Snap...
 
I have found that if the bimini supports near the stern are not connected, it is easier to install the glass after the winter. I have a two piece bimini over the cockpit so I will disconnect the support pole located about mid-cockpit to install the forward glass and then pull the support pole into place once all of the glass is snapped. Repeat the process for the second bimini. This seems to allow enough slack to snap everything. After a week or so the glass returns to normal size.
 
1) Zip each zipper just a few inches till all the snaps are snapped.
2) pull the bimini poles down with your hand slightly.
3) Start by snapping the snaps at both ends of each panel and work your way to the center.

Mine aren't too tough but if I use the above steps its easier.
 
Thanks for the tip about the extend a snaps.. I just ordered 3 packages from defender.. I have a snap tool but on cold nights it's still a bear to get the front panels snapped.
 
TIC wait until this saturday to put it on, 80+ can not wait!!!!
 
I used to have the same problem every year. So, I moved to Florida. Problem solved. Never have had to mess with it again. :)

quote:

Originally posted by kmont97




 
A tip we got from our marina is to use silicone spray on the zippers. I had a couple of stubborn ones and after I sprayed them, they went up and down with ease.
 
I forgot to mention that the silicone spray works great on snaps too.
 
like every body said let it set and get warm,I had a snap on cover on my pick up BAD IDEA!!!
if the temp was below about 65 or 70 there was noway it was going back on!

woosterken
 
Back
Top