Installing a drain plug

mmanna

Member
Joined
Apr 29, 2008
RO Number
29973
Messages
46
A question for the group. I have a 23 ft Chris and last weekend, when removing the brass drain plug I noticed water bubbling from around the sides of the brass bung. The fiberglass/transom is solid but the bung was rocking (i.e. loose). I am going to replace the whole thing but was planning to clean the fiberglass, scuff it with sandpaper and just seat the bung with epoxy and attach with the normal SS screws. I want it to be a permanent instillation with no leaks. I have used caulk in the past on other things but prefer epoxy when under the water line. Does this sound reasonable?

thanks
 
Epoxy or 3M 5200 sealant, around the garboard lip as well as the screw holes. Let it cure for about a day or two, but it won't leak anymore.
 
First, to make sure we are on the same page:

Normally a drain assembly is composed of A) a hole in the transom itself. B) a brass tube or tube-like with flange that seats more or less permanently into the hole (a) and C) a plug, either threaded or and expanding rubber "cork".

If you are discussing (B), the metal insert into the transom hole, then you must first do a few things. Remove the old fitting. Make absolutely sure that the core of the transom is dry, and that the core is not rotten. Since you "...noticed water bubbling from around the sides of the brass...", I would assume that water has gotten to the core. This -must- be remedied prior to re-attaching a fitting or further, serious damage could occur. If water has not gotten into the core not, and the hole and core are dry, then coat the sides of the hole with 3M 4200 or type 101, "pre-wet" the insert with a thin coat of sealant, then insert into the hole. Allow the sealant to "set" ( a few hours), then use the screws, covered with sealant, to finish the attachment to the transom.

I would not use "caulk" or epoxy for this task. If you are convinced that you will -never- need to replace the fitting, use 3M 5200, but I would not recommend it. I prefer either the 101 or 4200.

-edit-

Mssr. Msibley types faster than I do and posted while I typed. Two different methods, both work, in different ways. The choice is up to you.
 
take it out and see what’s up. there may be water in the transom. At the very least let it dry before any repair.
 
The transom is dry and not soft in any way. I don't think it was leaking (yet) but was probably was going to start soon. IMHO the bubbles were from rain water between the flange and the hull. I have the flange insert out now. I plan to use some liquid epoxy to coat the inside of the transom hole as well as between the brass insert and gelcoat. This way there is no exposed wood. Thank you for your input, I do have some 4200 but wanted a little faster set time. If I have any concerns then I will run it by my local yard. They are great guys and *very* honest. Thanks
 
you mean it was exposed wood when you removed the insert????????
 
I have mentioned a few times. The very first thing I do when I get a 'new' boat is sh*t can the garboard type drain plug. They are one of the main causes of water intrusion into transoms(but not the only one). So far, the last eight boats I had, had a garboard drain that had loose screws which let water into the transom. They usually took a few weeks to dry out as well as digging out as much bad wood as possible. I won't go into detail of how to dry out a transom now as you don't seem to have the problem.

I always replace with the brass tube and rubber 'bottle stopper' type plug. I drill out the garboard flange fitting so the brass tube will slide thru so it acts as the external flange. I silver solder the tube to the flange. Get a large brass washer for the inner flange. The brass tube should be about 1/4" longer than the drain hole with the inner washer. You have to make a swedgeimg tool which consists of a bolt and 3 washer. The swedge is the inner race of a ball bearing that just fits inside of the brass tube. Run the bolt and washer and inner race from inside of the transom and tighten down the nut and washer from the outside. The inner race will bell out the inner end of the tube as you tighten down the nut and make a very tight fit...much along the lines of how a pop-rivit works. Seal the tube in place with a proper sealant.
 
I will look closer this weekend. Luckily the transom is in extremely good shape. I just had the power package replaced (OMC to Merc) and the marina did not find a single bit of wet or soft wood. Not bad for a boat that is 22 years old. Charlie I will ask my local yard to see what they say about your idea. Since I have to replace it anyway I am willing to go the full distance. I prefer to have a plug that screws in so I am not sure about the expanding type of plugs. I have in the past installed the garboard type drain plug using putty epoxy and been very happy with the results. thanks for the help.
 
Back
Top