JABSCO electric head problem - FIXED!!

laramr

Member
Joined
Jul 19, 2007
RO Number
27577
Messages
78
I haven't gotten any responses in the Plumbing/Sanitation department so I thought I'd try here. Went to use the head for the first time this season and I think my motor is seized. When I try to pull water (raw water feed- and yes the seacock is open) into the bowl I don't hear anything. Light dims, so I know its pulling amps, but no other signs of life. If I hold the switch in either direction for more than a few seconds I get a three-tone beep (overheat warning?). Any hope other than replacement? Rebuild? Did I miss something stupid? Where is the best place to get a new one? How big a job to replace? Thanks for any and all help.
 
I suspect you're right; the motor is seized. If you disassemble it you may be able to free it up (if it's not already burned out) otherwise you may need a new motor. You won't know till you get it apart.
If you can find the model number you can go to the Jabsco web site and find exploded diagrams, parts lists, etc. If you want to go the replacement route Boatfix can "fix" you up.
 
The Jabsco electric on my 2765 did a similar thing in that it would trip the breaker when I tried to flush. It turned out that the top impellar in the unit had swelled and was not turning. You can check this by loosening the screws on the top of the unit a little and then flushing. loosening the screws should allow the swelled impleller to turn. Some water may come out but you can see if the its the impeller or the motor. I doubt the motor has seized. You can get a repair kit from Jabsco which includes an impeller.
 
I had the same problem with my Jabsco electric head. I was able to remove the motor and rebuild it. In my case, the motor armature was severely rusted. I was able to take it all apart, and clean it up. It was so bad the field magnets had come loose, but I epoxied them back in place. It's still working today after 1 full season use. Sure beat buying a new one. So if you want to try the repair it may be possible depending on what you find.
 
Thanks guys. I'll try the tear down and inspect. Not much to lose at this point.
 
Here is a link to the tech sheet ( PDF ) for the head you are likely to have.

Make note of the "Service kit". Each model has it's own, and, though it is not specifically mentioned in the info sheet, servicing a marine head ( with the kit ) is generally considered an annual maintenance item.

--edit--

One other item: From the tech sheet:

After long periods of non-use, toilet and pump may dry out.
To ease initial start-up, put about one quart of water in bowl
and let stand awhile before initial use.
 
Mike, when you post a question on a weekend, you ain't likely to get a reply (at least from me) before Monday. I agree with the others, the motor is likely seized up. But when you post a question, it's best if you can supply as much information about the particular head as you can. Jabsco makes 6 or 8 different electric heads, and if we know which one it is, it helps a lot in trying to figure out what the problem might be.
 
Mine was also seized up this spring. However, I took the cover off of the motor behind the head and was able to easily free it up by turning the exposed shaft with a straight screwdriver. It's been fine since. I think the impeller dried out over the winter and got stuck to the housing because once it got wet again it worked fine. It's easy to try and a lot cheaper and easier than changing out the motor.

Bob G
"Liberty"
East Greenwich RI
Mainship P34
 
What?! You don't sit at home on weekends waiting to help us with our heads?! What kind of moderator are you? :) Sorry if I seemed impatient Vic but I was trying to decide whether to hand it over to the marina to fix. The unit I have has this next to the bowl. http://jabsco.com/files/29200_electric_conversion.pdf Not certain of the model number since the label is worn. Hope to get some time one evening this week to open it up and get a look see. Will try to remember the camera. Thanks everyone for your replies. I'll report back.

quote:

Originally posted by Vic Willman

Mike, when you post a question on a weekend, you ain't likely to get a reply (at least from me) before Monday. I agree with the others, the motor is likely seized up. But when you post a question, it's best if you can supply as much information about the particular head as you can. Jabsco makes 6 or 8 different electric heads, and if we know which one it is, it helps a lot in trying to figure out what the problem might be.




 
Mike, that's Jabsco's electric conversion unit, to electrify a head that was originally manually-operated. Someone (previous owner?) added it as an aftermarket item. That unit is never used as an OEM item.

My personal opinion of them isn't very good. They do work, but they're noisy enough to wake the dead, and they're quite power-hungry. It just might be the time to think about getting a whole new head...

As far as weekends go, I have 2 1/2 acres of grass to cut every week, so I don't get to spend much time on the computer during the weekends.
 
My head did the same thing this spring. I took it apart to remove the tampon string from the shaft. Lubed things up and it has been working fine since. Last year I found the tampon and removed it but didn't get the string that was behind the grinding mechanism, near shaft. I guess when things dried up over the winter, she didn't want to spin anymore.

Take it apart and have a look.
 
The install looks factory and the breaker panel has an electric head switch. Anyway, I took it apart tonight. Was able to get the vise grips on the end of the motor shaft and break it free. I reassembled an now she turns! Empties the bowl like a champ, but I'm not getting water in. Seacock blocked? Will remove the hose at the seacock and slowly open to check. What if nothing comes through? Should it be cleared from under the boat or should I try to push a snake through from below deck? I'm a newbie so don't assume I know what the heck I'm doing. Thanks
 
Sounds like a dumb question, but, hey, someone's got to ask it:

A marine head usually has a switch ( valve ) to select "bowl rinse" or "dry flush". Fluid in the bowl will be pumped out in either position, but water will enter the bowl only if "bowl rinse" is selected. Did you check the valve or valve position?

( btw: please, don't be offended. I always ask the obvious because posters here come in all levels of experience. The goal is for all, including me, to learn. )
 
No Offense! I like when things have an easy answer because I did something stupid.

The unit has a rotating activation switch. Turn it clockwise and it draws water. Counterclockwise and it empties the bowl. Motor runs strong in both directions. I'm just not pulling water.

quote:

Originally posted by Radioactive

Sounds like a dumb question, but, hey, someone's got to ask it:

A marine head usually has a switch ( valve ) to select "bowl rinse" or "dry flush". Fluid in the bowl will be pumped out in either position, but water will enter the bowl only if "bowl rinse" is selected. Did you check the valve or valve position?

( btw: please, don't be offended. I always ask the obvious because posters here come in all levels of experience. The goal is for all, including me, to learn. )




 
At this point, I have a few "potential sources" on my list:

a) there is a clog. IMHO, not very likely, but it does occur.

The next two apply, esp if the pump has not been serviced on time/correctly.

b) the inlet side is not pumping due to broken vane or equivalent
c) the check valve(s) are stuck.

Most of my experience ( way, way too much experience ) is dealing with manual Jabscos... So I could easily be wrong in my list of guilty parties.

--edit--

double checked the manual, looks like my above statements should be related to the inlet pump vane and the control valve.
 
FIXED!

When I removed the inlet line and then opened the seacock I still got absolutely nothing. Figured there was too much air in the line for the motor to pull. Filled the line from inside, and problem solved! Momma has her potty back!
 
I'm glad you found and resolved the problem. And thanks for letting us know. :)
 
Back
Top