Jammed Steering

RonF

Member
exMember
Joined
Jul 8, 2004
RO Number
14220
Messages
55
I planned to use the boat today, but had to cancel due to the steering being jammed hard-over to starboard. The boat is a twin inboard with Teleflex cable steering to the rudder tillers. The last time I used the boat, I had to return and back into the skip on one engine. So, in the struggle I must have turned it all the way and then left it that way a few weeks ago. I normally keep the exposed portion of the control rod well lubed, so I am surprised that it got stuck in that position. The rod is now almost fully retracted into the sheath.

I tried to free it by using a block of wood as a lever against the tiller, and by pushing on one of the rudders from under the boat. It won't budge, and I am afraid to force the steering wheel.

Does anybody have a suggestion of what to try next?
 
My boat steering cable siezed over the winter. Six months in Zero degree weather with no movment at all.

Here's what I did. I probably should have purchased a new cable, but I'm so much the fiddler that I wanted to know what happend, and when I saw it I just lubed it and that solved the problem.

I took the cable end off back at the engine first. That was the easiest. Then I could see the Cable was siezed inside the housing between the helm and the engine. You have to verify what is siezed before you go any further.

I went up to the back of the helm and took the cable off. The helm was nice and free, it was the cable siezed inside the housing.
I began to work the cable. A little bit at a time until I finally got it to move a little.
Then I chucked the engine end in an electric drill and began to rotate the cable slowly.
(I discovered a kink by watching the cable housing wriggle like a snake, and re-bent the cable so the kink went away)
The cable had some kind of a Zerk fitting up near the helm. I tried to force some light mineral oil in that Zerk. Didnt work.
I tried some cleaning solvent and that went in. Finally all that black corrosion and gunk began to ooze out from the housing back at the engine end. (drill turning the cable all this time)
Then I followed that with some light Graphite oil. When I got through the cable moved almost 'drop free' in and out of the housing.
That was still working two years later when I sold the boat. Smooth n' easy, just like new!
 
Old Houseboater posted the best idea I've seen on freeing up cables about a year ago. Do a search and try to find it. I can't remember all the details.
 
I freed my sticky shift cable by disconnecting it from the shift lever. I then lifted the cable so one end was higher than the other as much as possible. With a cordless drill I drilled a small hole near the end in the plastic housing. Using an applicator bottle with a small nozzle end (a can of 3 in 1 oil would be perfect) I filled the plastic housing with motor oil and let the cable sit. I repeated this several times for a few days. The oil slowly drains down in the cable and frees everything up. Cable was good as new.
 
Thanks folks. This is a bit more complicated, being an inboard intallation with rudders. But, I see that I will have to first disconnect the cable from the tiller arm and maybe the steering wheel, just to isolate the problem.
 
quote:

Originally posted by RonF

Thanks folks. This is a bit more complicated, being an inboard intallation with rudders. But, I see that I will have to first disconnect the cable from the tiller arm and maybe the steering wheel, just to isolate the problem.






And I was just about to recommend the old heat 'n' beat. But the same caution with outboard steering would still apply - be careful about greasing too liberally, or you just end up with a congealed packing of salt, dirt, and gunk seizing things up solid.
 
A 310 Dancer with cables??? That's not very upscale. Not for SeaRay.

Anyway, it would still be important to isolate the problem. Could be a bent rudder stock.
 
hydraulic is a little common on inboards isnt' it ? i agree, start by disconnecting the cables and the tillers and see what is stuck.
 
put small hole in the end of a condom, and slide it over the end of the cable until it's over the plastic part of the cable. Fill it with penetrating oil and elevate it as much as you can.
 
Depending on how long it sat, there may be hard growth on the rudder and post.
 
Back
Top