Kohler Generator

Brav Eau

Member
Joined
Jul 3, 2007
RO Number
27190
Messages
5
I have a 5kw Kohler Generator that overheats after 10-15 minutes. I have tried just about everything. I'm not sure what the water flow should be from the exhaust but the lines leading to the water pump all seem to be good, I put a new impeller, I checked the heat exchanger and it is in top shape, the circulating pump for the anti-freeze seems to be intact. if the generator was in a more accessible location I would have it taken out and checked on "the bench" but Carver did not put this in to take out without moving both my 350's!
anybody with a great idea, please respond!

Brav Eau
 
Have you changed the coolant, removed a coolant hose, or let the coolant get low lately? If so it may have an air lock. There are two ways to fix it. First make sure your coolant recovery bottle is full and the tube is unclogged. Then run the genny till it shuts down. As it cools it should suck the coolant in the bottle back into the heat exchanger if the air lock is broken.

Second and faster way. Go get a radiator pressure tester. You can rent them at AutoZone. Make sure the heat exchanger is full of coolant. Put on the pressure tester and pump her up to about 20 psi. Should break the air lock.
 
are you certain that the inlet lines and outlet lines are clear?????
 
If the old impeller had any missing fins? they must be found and removed or water flow will be restricted causing the unit to run hot. The missing fins normally catch right in the neck of the impellar housing where the output hose connects. Double-check that especially if you don't have constant good water flow from the exhaust port.
 
How about the water intake strainer or the thru hull scoop strainer--often trash, fish, shells, jelly fish etc can be lodged in these intake areas.
Agree with the checking for parts of vanes. Did you pull the heat exchangers and clean the tubes?
 
You said - "I'm not sure what the water flow should be from the exhaust" - are you getting any water? it usually flows out pretty good, if not maybe you have a defective impeller?
 
all great suggestions and thanks,
the old impeller had a torn vane but still intact so I hope we can rule out a clog somewhere in the system. I like the idea of setting up a radiator pressur tester. when this started to happen I did drain the anti-freeze to check the heat exchanger and refilled it this weekend and it still shuts down. Perhaps there is an air lock inspite of refilling.
I did check all the hoses from the water intake, through the filter and into the water pump and all is clear.
I am fearing the worst though and I think Pleasure Time may have a point in that there could be a piece of something lodged inside somewhere to impede water flow.
I don't know if there is simple solution to solving that without dismantling the motor.
thanks to all for the feedback.
Saint JOhn NB

thanks to all for contributing.
 
first, check the exhaust flow. how long have you had the boat? whenever I start either the mains or the genny i ALWAYS check the flow out the exhaust... it's much better to find out you have a problem while at the dock !

you should have a good flow, I know that sounds vague... and the noise will be muffled.

if not, and since you've checked the strainer, make sure you dont' have something stuck on the thruhull although since gennies dont' have scoops like mains and AC, you're less likely to have a plastic bag stuck in there.... but go under and check it out anyway.

BTW, this may sound obvious but are you sure it's actually overheating ? do you have a gauge ? or an IR gun ? could be a defective temp switch.

how about the Thermostat ?

if you have no raw flow, it woudl likely overheat before 10 or 15 minutes... does it happen regardless of load ? with no or little load, it shoudl run cooler.
 
When you refilled the heat exchanger did you remove the vent nut at the top of the tank? This allows the air to escape as you fill. If you did not remove the vent nut, I would check for air lock.
 
Back
Top