Leaking Beer

Pilotpak

Member
exMember
Joined
Feb 18, 2007
RO Number
25250
Messages
185
Ok..This is a stupid post I know,... I'm just curious to see if anyone else has this problem.

I usually store two or three cartons of beer (in aluminum cans) in a nice lined bunker under my lounge. These are normally stored flat in the carton.

Almost, every time I open a new carton, two or three of the cans will have leaked [:-drool] , obviously the cans are scuffing against each other whilst the boat is in motion.

I'm just interested in seeing if this is maybe due to our local manufactorers (Australia) using poor or thin quality cans, or if it's a common problem. Years ago, our beer cans had platic rings, which I guessed would have helpped prevent rubbing, but these are no longer used (not dolphin friendly !)

132600.jpg


I'll probably have to make some kind of storage bin with dividers to stop the cans rubbing. (BTW..I use cans so they can be crushed, due to limited garbage space on board).

Wayne
Larson 310
 
Sounds like a very serious problem!!! Must be a problem isolated to the southern hemisphere. No such issues here.

Cheers.
 
This is a VERY serious issue! We need to band together to try and get to the bottom of this!!!!!!

I'd be happy to send you my used plastic rings if you think it would help.

Perhaps it's a heat issue?
 
"Years ago, our beer cans had platic rings, which I guessed would have helpped prevent rubbing, but these are no longer used (not dolphin friendly !)"

You mean the dolphin down there, drink beer?!
 
If I where you, I'll present a formal claim to the Larson Design Department, a limited space for BEER is unacceptable.
 
Why didn't I think of this earlier... The answer is obvious. Your suppose to drink all that beer, not store it. Duh!
 
Alcohol abuse !!!!

A restraining order should be issued to protect the beers.

From a proud Canadian !
 
Sounds to me like you have a serious issue with the brewer using thin aluminum cans. Some suggestions:

1. Switch to Foster's if you can. Does it still come in big steel cans?

2. Slow down. What's more important: getting there first or having a good time when you get there?

3. How long has that beer been in the boat? Without refigeration beer can go bad in a couple of months. Six months in a reefer is maximum.

4. Upgrade your brew to something that comes in bottles.
 
Your beer is defective, send to me for disposal...
 
kegerator.

HMMMMMMMMMMMMMMMMMM

How do I sneak one of them past the Admiral?

HMMMMMMMMMMMM

That along with the weekly refills?

HMMMMMMMMMMMMM
 
All the other guys are correct but in addition those cans are very thin and any vibration or salt corrosion does them in. Use bottles for no worries.
 
Do you buy the thin cans so you can crush them between your chin and chest? I had never heard of this before but someone rcently told me people do this. You might try buying an import with a sturdier can, although some yanks have been known to do butt crushes with Buds so they might fail as well. This may well be one of those world problems that is just too difficult to address.
 
Based on my highly unique degree in Beerology, I am aware of the situation and have figured how to save the situation. You need assistance with handling the beer. I am quite of a group called HOOTERS. They are excellent at saving the payload. They even well known in the area of proper disposal of the payload if needed. If you need assistance hire a few of them and I will personally come train them in the art!

hoot.jpg
 
quote:

Originally posted by Pilotpak






Need more information before we can help you.
Is the can leaking from the top ? the top is about .0062 thick without the overvarnish coatings. The midwalls are around .0038 thick not including ink litho or varnish either, the bottom which is most cases takes the most abuse is around the .004 thickness. the Aluminum cans have become quite thinner since the 70's where one was more difficult to crush. Anyone old enough to recall how much harder it was to hold a can out and crush it? now a kid can do it.

Abrasion seems to be the problem and since cost savings are huge with thinner metals, I suspect the over varnish is also to thin....
Or maybe, just maybe you just let them sit in one place to long and should be encouraged to drink more often and improve the cycle counts.
Hope nothing else going wrong on your fine boat.
 
Clearly you are not drinking the beer fast enough.
 
Back
Top