Manifol/riser temps?

SCORPIO

Member
Member
Joined
Jun 1, 2001
RO Number
4810
Messages
966
I'm considering purchasing a new to me boat with a pair of RWC 5.7merc with alpha one outdrives. The boat has one new engine (port) with about 70 hours on it and both engines had new risers and manifolds installed in 2005 with very little fresh/brackish water use. We sea trialed the boat yesterday and the surveyer mentioned to me that both engines had manifold and riser temps of about 180-190 degrees at cruising speed (3200 rpm) as measured with an IR gun. The engines themselves ran rock steady at 145 degrees the entire time including several minutes at WOT (4200 rpm). The surveyer suggested that all the manifolds and risers should be replaced due to high temps. I didn't think that 190 sounded excessive for crusing temps. I cannot seem to find a spec mentioned anywhere as to the correct operating temp of manifolds/risers. It would seem to me that they would run hotter than the block temp due to the hot exhaust being dumped into them. The owner is not of the opinion that the risers are too hot and doesn't believe he should replace them. This puts me in an ackward spot, I don't want to kill a good deal based on this info. What do all of you think about these numbers? We can get the boat at substantially below book price and we like the layout and general condition of the boa. I'm thinking about doing the deal and pulling the risers and cleaning/inspecting them. If necessary I can replace them myself for only the cost of parts and a day of my labor.
Opinions please
Thanks
 
I don't think I have ever heard an exact temperature, but 180-190 sounds hot. I use the old fashion, place your had on top of the riser, it should not be so hot that you cannot hold your hand on it. On all my Mercruiser engines, one riser is always hotter than the other. Currently on my 4.3, the STB riser is somewhat hot, but I can still lay my hand on it and the Port is not hot at all. This is at idle, I would think it would be hotter at speed.
 
Doesn't sound like thw water pump is bad but the manifold/riser temps are high. That kinda leaves the risers(with some of the smallest passages) to be the most likely cause of reduced circulation. Heck, drain the water from one of the manifolds and pull the riser.
 
Charlie, are you suggesting cleaning the risers or replacing them? I know risers are alot cheaper than manifolds. Would replacing just the risers be a good idea, assuming the manifold passages are clear? Also, can you pull a riser with the boat in the water or do you have to haul out?
 
Mine run cooler than the 150 degree temps I read off the block at cruise. Yes, I can keep my hand comfortably on the exhaust elbows at cruise.
 
Before you get too excited, I would get a second reading with a different IR gun.
 
I second DiveDaddy on doubel checking teh temps with IR and or hand test

Risers and Manifolds are "wear items" and you can factor in the cost to your deal. It is something you do not want to mess around with.

On my 4.3 My risers run 150-160 at cruise and I can put my hadn on them for a while (it does get uncomfortabel) 180-190 is hot.

I would get a quote for parts from Boatfix, and mayeb lower the offer by that amount or split the cost of pars equally. If I remember correctly merc parts are about $800 per engine and Sierra about $450 per engine (manifolds and risers)

Lastly the surveyor will tell you to replace things that are or near failure, it's his job. It's really up to you and the seller to work out the details. 3 years is about the recommended replacement interval in salt water RWC. The overall use is not the issue, in fact the light use may have exasperated any decay if the water sitting in them had salt content
 
Chris,
The engine/manifolds are higher than the water line so all you have to do is drain one side manifold and pull the riser to inspect. That way you can tell if it's the cause and work on adjusting the price accordingly.
 
quote:

Originally posted by BillK

I don't think I have ever heard an exact temperature, but 180-190 sounds hot. I use the old fashion, place your had on top of the riser, it should not be so hot that you cannot hold your hand on it. On all my Mercruiser engines, one riser is always hotter than the other. Currently on my 4.3, the STB riser is somewhat hot, but I can still lay my hand on it and the Port is not hot at all. This is at idle, I would think it would be hotter at speed.






DITTO...
 
There is a similar thread in the engines forum.

I just started my 1999 5.0 liter Mercruiser and let them run about 20 minutes. Once the engine was at full temp, the temp at the top and around the risers and manifolds was 60-70 degrees. I had one spot that was 90 degrees. I'm sure that if I let it run longer the temp would rise slightly. The general rule is that the manifolds and risers should never be too hot touch even after running. So what's that 100-120 maybe 130 max? Another important consideration is that the temp is more or less consistent. If it's not, there may be a blockage or gasket leak. That 90 degree temp that I found was at a riser bolt that I found was loose last fall. No surprise that the gasket failed. New gasket is on the list for the weekend.

Good Luck
 
Think about how hot your water heater water is, 120-140deg? That's too hot to hold your hand under and hotter than your riser should be..
 
most people will not hold something that is about 140F
 
I'm going to replace both engines risers and manifolds before we start our season with the new to us boat. I don't trust having a yard I don't know work on it. For all I know, I'll get a spray can overhaul with a real parts bill. I've done these before so I'll take some Advil and have at it.
BTW what brand of risers/manifolds do you all like? I've always used Osco.
 
Osco is fine. Sierra was backordered for a while.
 
Back
Top