Marine Gas???

OmeOmy

Member
exMember
Joined
Sep 11, 2006
RO Number
23180
Messages
37
Reading latest BoatUS magazine and on page 9 is an ad for ValvTect, a marine "specially formulated" gas. Now I have only been boating for two years but never knew this fuel existed. Anyone have any thoughts on this product, ad says it reduces fuel consumption, extend engine life and a few other things. They have a dealer locator on their website and just so happens we have a nearby marina that sells the stuff. Been by that marina and always wondered why they were 30/40 cents more than everyone else. Paul.
 
ValvTec adds only pennies/gallon to price of gas; not 30 or 40.
 
"always wondered why they were 30/40 cents more than everyone else"

..because boaters will pay it? [8)]
 
Only good for old engines that were designed for leaded gas. It has a lead substitute in it. The rest is "snake oil"!
 
Yeah, if it's the same stuff from 20 years ago. It was just a lead subsitute additive. Not sure what is does now.

Just googled them. Except for stabliizers(which you can just add yourself), it's pretty much like what Steve said... 'crap'.
 
FWIW- From their website: Compared to non-marine grades of gasoline or diesel fuel, ValvTect Marine Fuels contain more detergents, stabilizers, water dispersants and other important additives.

The diesel version also contains bug- and veggie-cides.

The lead substitute stuff was long ago.

I usually use their marine gas because my engines continue to run really well with the stuff....and because it is actually offered at slightly lower markup than other local dock suppliers I have had less success with. If I had known my engines would run so well on 'crap' I could have saved a lot more- who knew? :D
 
Sandy, I've got a bridge in Brooklyn available for sale. :)

Just joshing----If it works better for you----stick with it.
 
Stabilizers? I use Sta-bil

water dispersants-alcohol

detergents-paint thinner

I guess it takes 38 cents a gallon to mix 2 cents worth of ingrediants.

Sandy,
I respect everything you have to say concerning boats but I just can't see paying for additives. Especially if they already are included. The Only additive I've ever heard Geo mention is Techron.

I can see marina gas needing a bit more stabilizers because of slower turnover. I get my gas from the cheapest local gas station.:D[:I]
 
When I take on gas, I'm pumping 200+ gallons at a time. For that kind of coin, I'll pay a little extra to get the best gas my money can buy. I buy Valvtect 93 octane. I'm not a chemical engineer and don't pretend to be one. Despite what the know-it-alls claim, I know three things:
1) My boat seems to run better
2) Most of the better marinas around here have it
3) the info on the Valvtec website looks impressive.
I have no reason to be skeptical of the claims (besides corporate paranoia) and I seek out Valvtec and use it. I don't recommend it...I'm just saying it works for me.

Jim
 
quote:

Originally posted by sugilbert

Sandy, I've got a bridge in Brooklyn available for sale. :)

Just joshing----If it works better for you----stick with it.






Steve-How much ?? If you give me 50% off I'll take the right side as that's the only side I use anyway... .

The Valvtect I use is 87 octane, exactly what Crusader has set their engines up for, for best performance and state specifically performance may be degraded with use of higher octane unless pinging is detected.
I did mention it is actually cheaper here , not more expensive? It also seems to be the only spot in that harbor I know of that carries 87oct, not just 89 & 93.

Jim- Does your engine mfgr prescribe 93? If not, you are getting less potential BTU energy /gal than lower octane, .... but then any additives found in all marine gas and apparently especially Valvtectwith it's extra stabilizers,etc. would somewhat dilute the energy content that puts the GO in the boat.
 
Yup, Tho not noticible in lowering mileage(IMO), octane is an additive that actually lowers the fuels explosive ability, OR, it lowers it's burn rate to burn more evenly and completely. Fuel/air under compression wants to explode. The spark just kicks it off. You don't want an explosion. Octane additives slow down the flame front. Also, Using octane higher than you need is a waste of money. Stabilizers would not be, especially in larger tanks.
 
This topic is great. I just came from my boat and changing filters.

There is a big debate here in NY about whether gas station gas is different from marina gas. Does anyone know with any certainty that there is a chemical difference? Not Just that "My cousin Jimmy, whose brother was a mechanic says..."

What additives can we use to overcome the lack of lead in the gas? What additives can we get to overcome the corn oil, 10 percent of the gas?

I have 25 year old Chrysler 318'3.

Thoughts?
 
Actually, Joe, there's no corn oil in gas---it's ethanol (an alcohol) distilled from corn--just like the moonshiners did.

If, in fact, you have a really old engine that requires leaded gas (it was a lubricant), then there are additives sold for that purpose.
 
"How old is "really old" for an engine?"

For the purposes of leaded gas: around 1978 & earlier.
 
Capt Harry We do not recommend putting all of one's personal info such as address and phone number in forum postings. These forums are open for all eyes to see........... Have a good one!
 
Steve:

Yes the engines are from the early 70's and rebuilt 6 years ago.

What additive can I buy to add lead?

To offset the Ethanol/Corn oil?

Thanks,

Joe
 
Your rebuild probably made up for some of the 'lead' that was used in the old days. Other than the higher octane(controlled burn) of the fuel, like Steve said, it was a lubricant for the evhaust valves(mainly). Valve and guide material has overcome the need for the lead as a valve lubricant. There are lead subsitutes(valvtect makes some)for older engines needing a 'topend' lubricant.
 
Back
Top