Odd tachometer behavoir

  • Thread starter Thread starter blouderback
  • Start date Start date
B

blouderback

Guest
I got a little worried today when cruising up the Delaware. Normally, the tachmoeter reads about 2000 rpms at 20 mph, 3000 rpms at 30 mph, and WOT is about 4600 rpms and about 50mph. Today I was pretty heavy, yet the rpms showed about 4500 at 30mph. At first I'm thinking that the prop hubs have spun, but I'm pretty sure there are no hubs on a Bravo III. Performance did't seem off, and the engine didn't actually SOUND like it was running that fast. Nonetheless, I made sure to keep it under 4500 rpms. I was watching the tach like a hawk.

After a few miles, I look down and notice that were doing 30mph and the tach is right at 3000 rpms. I goose the throttle, and the rps and speed rise appropriately. I got WOT (for just a few seconds, 'cause the Admiral starts yelling at me that we're going too fast), and it never gets over 4500 rpms. All is well!

On the way home, same problem. This time, I tap the tach with my knuckle, and instantly it drops down from 4500 rpms to 3000 at 30mph.

What's going on???
 
On some of the old tachs (Not that 2005 is old!) you need to open up access to the rear of the tachs. There is a slot for a screwdriver where you can adjust the tach for 4,6 or 8 cylinder engines. Note the position that the slot is in and turn it left or right a few times and then put it back to the original position. Sometimes the contacts get dirty and moving the selector in the back cleans them out a bit and they reflect the right RPM's. I've done it on a few Sea Rays and some other boats. It's cheap easy and it might work. If not, you're back here looking for a solution!
 
Bob,

My 2006 twin-engine Larson recently started doing the same thing on both engines. When this occurs my Synch gauges still reads properly, so the problem is almost certainly in the tachometers. And since tapping the tachometers seems to fix the problem it would seem to be something in or near the gauges. I presume some connection is loose or dirty.

I'll try the fix that the previous post suggests the next time I'm on the boat.

Mike
 
Let me guess, you have Faria gauges?

I would not be surprised if you do as they ALL seem to go that way. What you did is known as the Faria Rap.
 
quote:

Originally posted by rommer

Let me guess, you have Faria gauges?

I would not be surprised if you do as they ALL seem to go that way. What you did is known as the Faria Rap.





Yup! That's it exactly. Welcome to the rap club.
 
My stbd tach (FARIA) Does the same. A good "rap" and all is well.
 
I've had it happen and moved the cylinder selector to clean to contacts and all was well.
 
I think I am a charter member of the "rap club".
Had/have the same problem on two boats. Sooner or later the hand will fall off. I took one tach out & CAREFULLY removed the face, put the hand back in the socket, has been working for over 2 years. Got to be really careful when you put the hand back on, get it positioned right! Have to glue the face back on. Worked for me, hope it works for you.
 
Yup, you guessed it, Faria. I thought Faria was a quality product, but I'm getting the sense that they're not.

Speedometer.jpg
 
Now you know why the Beltzville's water cops let you go heh. Your meter was way faster than your actual speed. ;0).
 
Weird... I was coming here to post the exact same problem with my 2003 Maxum 2700 over the weekend - i.e., the tach was reading higher than the engine was actually running. After a few minutes it fixed itself. Glad to know it is not a big problem. Anyone know why it happens?
 
I have the same problem.. My starboard tach will start out way off, then with a few raps' settles down..
This weekend we went to the south shore LI. (about 2 hour trip for us) and I noticed on the way down the tachs were synced and dead on correct, on the way back my SB tach was showing 300 RPM faster that the port but the speed was the same, and it sounded correct. rapped and rapped but it never corrected.

This year it seems to be an issue with the SB more that the port, last year it was the port and I rapped it so much and that the hour meter now reads 6304 hours... (actual is 432)

I am going to try the fix mentioned.
 
I wonder if Faria would recommend the "rap" method or "ratcheting the cylinder adjustment screw" method.

Hmmm, I think they would recommend a new gauge at $116 (for mine).

They are not getting my money until I get mad enough to put a knuckle through the lens.
 
"They all do that".

The "Rap-N-Tap" method tends to last for the duration of the voyage.
The "Use screwdriver and wipe contacts" method tends to last for a while ( a few to many trips ). The "suggested fix" is a new Faria gauge. The Cure is a gauge by another vendor...

This has been true for at least as long as I have been around boats ( Ugg! Don't many me count the years!!! )
 
Looks to me like Faria will fix or replace it for about $30-50 under their lifetime warranty.
 
Ah yes, the infamous Faria lifetime warranty as long as you pay us policy.
 
Back
Top