Prop me up!

WaxedElvis

Member
Member
Joined
Apr 20, 2006
RO Number
20940
Messages
126
If someone would be so kind as to educate me regarding props –

Twin 200 o/b's, I want to maximize range and have been told the right props can make a difference. This leads to several questions –
1) Is that true, if so what props do that?
2) How do I know what props I have now?
3) How much $ am I looking at to change them?
4) What do you do with used props?
5) Does it really make enough of a difference in effeciecy to justify the cost? (I'm assuming the cost is high because it's boat related.)
6) The answer to any other question I don't know enough to ask….

Thanks in advance.
 
This is not a specialty of mine, but here are a couple of points to get you started. All other things being equal:

1) Material - Steel, being stiffer, gives higher performance than aluminum, at greater expense. However, steel also has some non-performance downsides that are beyond the scope of your questions.

2) Pitch - Think of the pitch of the prop blades like the gears in your car. Low gear (low pitch) gives more power at the expense of top speed. High gear (high pitch) lets you go faster, at the expense of power. In the car, you can shift gears according to need. Not so, on your boat. If you are pulling water skiers, you may want more power, thus you will choose props with less pitch. For maximum cruising range on plane, more pitch is called for, within practical limits.

My car, for instance, has a 6-speed manual transmission. Its top speed is reached not in 6th gear, but in 5th. Though 6th is theoretically faster, it lacks the power to go as fast as 5th. So, you can overdo the pitch thing.

Number of blades and prop diameter are also relevant.

As for your used props, keep them as spares, to be installed together, if needed.
 
1) Yes, the right prop can increase performance and fuel mileage.
2) The props should be marked with a number like 14" x 17", with the second number being the pitch. The first number is the diameter, which really doesn't matter all that much.
3) Props can run anywhere from $100 to $500, depending on brand and material (aluminum or stainless steel).
4) Keep used ones as spares, or sell them on eBay.
5) Definitely.
6) Sometimes, prop shops will let you test props before you buy. Check around...
 
What is the difference between a dual prop and single prop? Also, are they interchangeable? can you convert a single to dual and dual to single.
 
Dual prop has two props on one shaft, counter rotating. There is no conversion, you will need to replace the whole outdrive.
 
quote:

Originally posted by blouderback

Dual prop has two props on one shaft, counter rotating. There is no conversion, you will need to replace the whole outdrive.






What is the difference between performance/efficiency? Is it better or worse.
 
The correct props will not only give you the best fuel efficiency but you also have to consider the toll the wrong prop(s) will have on your engine(s). A prop with too small a pitch could result in the engine exceeding its maximum RPM rating (over revving). A prop with too large a pitch could result in the engine struggling more which could foul the plugs and/or cause other hidden damages.

Your engine manual should have a recommended RPM for Wide Open Throttle (WOT). Figure out the recommended RPM at WOT; then take your boat out and open the throttle all the way and trim the engines. Note the RPMs at top speed. If your RPMs begin to exceed the engine manufacturer's recommendation, back off the throttle. This would mean your pitch is too small. If you can't get to the recommended RPM level then your pitch is too big (assuming you have a clean hull). A good rule of thumb is approx. 200 RPM for every one inch of pitch. For example, if you're getting 4500 RPMs from a prop with a 15 inch pitch and increase to a 16 inch pitch, your RPMs should drop about 200. That is certainly not an accepted mathematical equation that fits all situations but simply an approximation.

Stanless steel props don't bend or flex when running where aluminum props will bend a bit which effectively decreases your prop pitch (typically by one inch). So if you go from aluminum to stainless (or vice versa) keep that in mind.
 
It can take a while to find the right props, but that will get you the results you want - or the closest to it.
First you'll have to get your engines running the best you can. It's no use doing this with stumbling engines.
You'll also want your boat hull in best condition - clear of marine growth and freshly painted (if it's painted).
Finally, you'll want to select props with your boat loaded like you plan to use it. So, if you are doing this so that you can take a cruise, or do ocean fishing, well, that's how you should load the boat - full gas, water, coolers, people, the works.
Finally, prop selection is primarily trial and error. But the best results will ultimately come from the best props - and those cost more money. They will be stainless steel. Get the right props with your boat set up like this and you will get the best results.
 
Dual props give you better hole shot because there is more prop surface area in the water (6 blades). Also cuts down the anomoly of "torque steering", which is when the single spinning prop tends to push the drive to one side.

Oh, and it looks cool when the boat is on the trailer.
 
Dual props ARE NOT available on outboards. Yam made some for awhile, but dropped the idea because it's heavy, expensive and does not have near the efficiency of a properly set up single, stainless, well matched prop.

Yes, I know they are used on stern drives. Compensation for the deficiencies of the drive system. Max performance stern drives are single prop.

For max efficiency, including getting the best fuel efficiency, you will want those engines propped right at the top of the recommended rev range. Somewhere about 5800 RPM for most 200s. That will allow the engine to spin freely at all speeds which gets the best efficiency. And efficiency is what gets gas mileage. Outboards DO NOT like to be lugged. Even the newer 4-jokes want to run in their max efficiency range. And that means 4000+ RPM for most of them.

Don't use an Aluminum prop except maybe as a spare. And prop for upper end of rev range with your normal load.
 
Please help! Hello I am new to boating and just brought a 1987 17ft bayliner cuddy cabin with a 75 hp mariner o/b motor that needed a new lower unit because the guy who had it backed into a rock. Now I brought a used lower unit off ebay from a 1981 mercury 80 hp and got it on but the prop that was on the old lower unit is beat up and not useable. The prop reads 48-77348A4-21 and I looked it up it says it's a 13x21. Now my buddie thinks thats to big of a pitch to be on that boat with me being a pretty big guy 6ft8 370 pounds and my family is larger to (not as big as me LOL)so could someone please tell me a good prop to start out with? Thank you very much
 
21 is way too big for that rig. I have a 15' Glasstream with a 115 and I'm running a 22". I would think 19" would be about max for that rig and a 17" would probably be better, especially if you intend to pull water toys. If you don't have a tach, get one and prop it for 6000 RPM at medium load, like 2 people and a tank of gas. That motor wants Quicksilver Premium Plus oil mixed at least 50:1. 45:1 is probably better and use only fresh gas.
 
There are many ways to arrive at the "right" engine/boat/propeller combination, but often the best bet and ultimately most cost effective, is to go to a well-respected prop shop in you area that will let you use a variety of props as loaners so that you can find the right one by trial and error.

Also, after you discover the best near match, the same shop can fine tune the prop for you. Not inexpensive up front, but in the long run, it is a very good way to deal with the issue.

--

W Elvis, in your area, some boat dealers might also have an array of props and will let you run through several to find the right one. And considering your area, there has -got- to be a good prop shop around. Ask the neighbors...
 
Back
Top