Prop Puller?

RM

Member
Joined
Jan 1, 2000
RO Number
468
Messages
325
Will an automotive gear puller work to pull a prop? Is a 18" diameter on a 1.5" shaft. Went to buy a marine one but they all seem to be a few hundred $.

Also any pointers on actually pulling them and reinstaling?

Thanks
 
You can try it. One tip, just back the nut off a thread or two, props pop off they don't just slide off. I've seen them fly across the yard with the nuts totally removed when the prop lets loose. I really don't think a gear puller will work all the props I have pulled took alot of force.
 
I used a standard 3 jaw puller to pull my 24" prop. Just make sure you've got the jaws on the hub, not on the blades! Jim P. is right, they don't come off slowly, it's one "pop". If you get a lot of pressure on the puller and it's not moving - sometimes a good whack on the end of the puller bolt will break it lose.
 
Most prop shops let you borrow a puller if you are getting them tuned-up. Like Jim said, keep those nuts on because they do fly. I just pulled mine and it took a lot of force along with a little heat from a torch. A few taps with a brass mallet and BOOM. Props came off.
 
I had my Chesapeake Bay work boat at a yard that caters to local watermen last season. Before I could reach for my prop puller, the owner and mechanic had the prop off using the traditional method - a 2"x4" and a maul on the hub.

You can spend $250 on a prop puller or use some ingenuity.

RM, where on the Middle Chesapeake Bay are you located? I have a prop puller collecting dust in my garage that is capable of handling upto a 1 1/2" shaft.

Mark
Middle River
 
Some pullers work with 3 bladed props but not 4. We have both, 4 on thew shafts, 3 for spares, which always presents a challenge with pullers.
 
All of the above is dead on. I used the puller loaned free from the prop shop. ABSOLUTELY loosen the prop nut but do not remove it!
 
A bit off topic, but I'm curious; would teflon tape on the shaft make it any easier. I have seen mechanics have to heat and cool the prop to get it off. Kind of scary to me.
 
Nothing likes to be hit. Had a particularly stuck prop once. Put the puller on it, tightened up, no movement, beat it around the hub, still no give, left it overnight with pressure on it, beat it some more the next day & off it popped.
 
Mark thanks for the offer what kind of puller is it? How much?
 
The prop puller isn't offered for sale. If local, I'm offering it to assist in the 'pulling' of props to spare you the cost of purchasing such. A boater helping a boater!

The unit is a Pro Pull #PPF-103
1 1/2" Max. Shaft Diameter Heavy-Duty Propeller Puller designed to remove 3, most 4 and some 5 blade propellers on inboard shafts.
 
I've made a number of pullers for different applications.

Pullers for shafts start with a pipe the is big enuff to go over it. It's length is determined by the amount of shaft protruding past the thing you're gonna pull. Weld a large hardened nut on one end with a hardened bolt running thru it. Grind the tip to a point to center on the end of the shaft. weld a chain to the pipe to correspond to each blade or if the forward end of the hub is easy to attach a hook, weld 3 chains. It's important to have the chains equal length from the weld.

Bring all the parts to a welder and he may do it for $25.
 
Mark
Can you send me a contact number? I tried to send you a PM but no luck I need one of those anchors.
 
David: Teflon tape or any other product is big NO NO. The props stay on because of the self locking machine taper (and the key) that is precision machined and concentric to the mating prop. Anything outside of that shaft geometry will cause problems with the alignment. For example, a raised burr on the shaft can cause vibration, while a negative defect: divot or pocket like, is not as much of an issue.
The torch heat on the prop works because of the thermal expansion of the Bronze or Nibral. The heat expands the inside diameter, and yes, too much can be a problem. Timing is a variable also. If you wait too long the heat transfers into the shaft, expanding that as well.
 
quote:

Originally posted by TJM

David: Teflon tape or any other product is big NO NO. The props stay on because of the self locking machine taper (and the key) that is precision machined and concentric to the mating prop. Anything outside of that shaft geometry will cause problems with the alignment. For example, a raised burr on the shaft can cause vibration, while a negative defect: divot or pocket like, is not as much of an issue.
The torch heat on the prop works because of the thermal expansion of the Bronze or Nibral. The heat expands the inside diameter, and yes, too much can be a problem. Timing is a variable also. If you wait too long the heat transfers into the shaft, expanding that as well.






Thanks! I learn something here every day.
 
And on that note, it's not unheard of for props to fall off when the shaft shears off right at the taper when the key isn't reinstalled properly.
 
quote:

Originally posted by jtybt15

I've made a number of pullers for different applications.

Pullers for shafts start with a pipe the is big enuff to go over it. It's length is determined by the amount of shaft protruding past the thing you're gonna pull. Weld a large hardened nut on one end with a hardened bolt running thru it. Grind the tip to a point to center on the end of the shaft. weld a chain to the pipe to correspond to each blade or if the forward end of the hub is easy to attach a hook, weld 3 chains. It's important to have the chains equal length from the weld.

Bring all the parts to a welder and he may do it for $25.






Charlie that is an interesting one. Using machine thread I presume? I had always thought that using the parallel beams with two bolts was a better approach since it would work on a few different sizes. The welding should be about the same no?
 
Dan,
I've made 'em with chain and arms that came from one of my other pullers and it seems to work fine but they're not as versatile as the chain. Also you have to make sure the tabs (that hold the arms)have a large enuff welding surface for strength. The arm type DO seem a little more secure because you make them to hook onto the hub instead of the blades.
 
Back
Top