Propellers

Msibley

Moderator
Member
Joined
Mar 9, 2005
RO Number
16534
Messages
1,745
I set up an informational sticky topic in the engines forum regarding propeller selection since the question arises here often.

I kept it simple...you can go read about the theories all over the web.

One note: it's okay to set up your props for a mission specific purpose. The big one being if you plan to pull water skiers, or, have heavy loads, then you might want to consider a lower pitched prop for the added "bite" out of the hole...and since you won't be running at WOT, this will also help to keep from burning your plugs up with the added strain of getting on plane.

I think I got all the idiosyncracies corrected in the thread! ;)
 
nice, a quick easy read.

it may be a good idea to add that diesel need to be able to reach WOT and then some. there is not a "range" like on gas.
 
Good writeup Mike. I would like to see the addition of composite props to the mix. With the interchangeable blades you can almost dial it in to the max RPM exact. One guy on the west coast had a 4 blade with two 16 inch pitch blades and two 18 inch pitch blades. It was a bizarre thing to look at because the blades were shaped completely different. Worked for him though.

Just curious. Why test with 1/2 fuel etc? I was always under the impression you were supposed to be fully loaded to test a prop to the engines WOT.
 
1/2 fuel, no psgr load is what mfgr recommends. I imagine because it would be indicative of what would be considered a neutral benchmark, as there is no way MerC, for example, could account for all the variables in load and capacity of any given boat their engine may be in. From there you can dial in up/down for a given set of performance data.

-edit

Keep in mind too, David, you load up a boat with full fuel, psgrs, etc and do your test, the second you off load the psgrs and the fuel is consumed, the weight changes and all of a sudden, you find yourself underpropped...like a bomber that "jumps up" after bomb release...the weight is gone and airspeed increases.
 
"Keep in mind too, David, you load up a boat with full fuel, psgrs, etc and do your test, the second you off load the psgrs and the fuel is consumed, the weight changes and all of a sudden, you find yourself underpropped...like a bomber that "jumps up" after bomb release...the weight is gone and airspeed increases."

feel free to correct me....is it not better to be under propped then over propped. personally i am propped to hit 200 rpm over with full fuel, full gear etc. that way i know no matter what the load i am ALWAYS on the right side of the loading curve.

to many boaters will prop a boat as stated below and be OVERpropped the rest of the boat life. lets face it i run with more then a 1/2 tank of fuel EVERTIME i leave the dock. i always have a "person load" and tons of gear.

you find that many educated people will have a boat repropped just after purchasing it. many take an inch or so off of pitch to get it right.

maybe i am wrong but a little prop work is much cheaper then short life motors.
 
You missed the part where I said this: "...would be considered a neutral benchmark, as there is no way MerC, for example, could account for all the variables in load and capacity of any given boat their engine may be in. From there you can dial in up/down for a given set of performance data."

No one is advocating you single-hand it with a 1/2 tank of fuel.
 
quote:

Originally posted by Msibley






Good job Mike,

Just see a math error.

"Without going into the scientific equations and theories, I'll simplify...A 1" change in pitch will create about a 200 rpm change. (Going from a 21 pitch to a 23 pitch will drop the rpms by about 200 rpm...comes out of the hole slower, but has more top end speed, and vice-versa)."

Shouldn't it be drop the RPM's by 400 in your example?

I also agree with the diesel MUST exceed Max. Load RPM. I like mine about 100 RPM over max load.

Also all boats get heavier each year (more junk to carry) and this added weight will effect speed and RPM's which should be taken into consideration.

Thanks for the great forum.....

Rich
 
Rcoff512:

It's not just diesel. I have had two prop shops in the last two months tell me they would not build a prop for me if they could not build it to max engine RPMs. My problem is the 6.2 Merc redlines at 5200 BUT the "V" drives redline at 5K. Their comment was that maxing out an engine lower than the rated max RPM overloads the engine. I asked 'is that only applicable in diesel applications?' Both said absolutely not.
 
Back
Top