Simple Depth Finder needed

Joeshoes

Member
exMember
Joined
Jan 1, 2000
RO Number
1967
Messages
601
I am going to buy a depth finder this winter. I had a simple sender that attached to the aft end of the boat and it constantly got ripped off by the speed of the boat.

I have a hole on the centerline that has a sender for an unknown (long since removed by someone else) unit. I plan to pull that one out and replace it with another of similar diameter.

My question is what brand do I buy? I only want a depth finder with a display not a multiple function unit. I also would rather not pay for and install a fishfinder. Just a simple thru hull depthfinder. I will spemd up to $500.
 
...ripped off by the speed of the boat?...what are you running??

hummingbird is probably the most basic i've seen...about $125 last time i looked
 
If you are looking for a depth finder only, mounts in a 2 inch hole and uses a transducer that mounts to the bottom. Check out page 38 of the boatfix cat. They start out under a hundred dollars.

Ken
 
I'd stay away from the Faria products unless you are very good at doing the Faria Rap.

I've never seen gauges with a higher failure rate. Their "limited lifetime" warranty is certainly going to be needed, I had one gauge replaced 5 times already.
 
I've experienced the "Faria Rap" on my tachometer recently, but have had no problems with the depth finder in the last 2 years. I wonder if the digital gauges perform better than the analog ones?
 
We just bought the 2 inch gauge type from our boatyard. It is a Hummingbird. While the boat was up on the
yard, they changed out the thru hull transducer, but it did come with the kind you install on the transom.
 
quote:

Originally posted by blouderback

I've experienced the "Faria Rap" on my tachometer recently, but have had no problems with the depth finder in the last 2 years. I wonder if the digital gauges perform better than the analog ones?






Could be true Bob but I just have a bad taste in my mouth with Faria products overall.

That said, their customer service has always stepped up to make things right but that gets old after a while. I mean how many times do you want to replace gauges?
 
Unless you are going to be shooting deep water, you might consider using silicon seal to mount the transducer inside. Worked for me on several smaller boats.
Jimmy
 
quote:

Originally posted by rommer

I'd stay away from the Faria products unless you are very good at doing the Faria Rap.

I've never seen gauges with a higher failure rate. Their "limited lifetime" warranty is certainly going to be needed, I had one gauge replaced 5 times already.





quote:

I've experienced the "Faria Rap" on my tachometer recently, but have had no problems with the depth finder in the last 2 years. I wonder if the digital gauges perform better than the analog ones?





Well my 2003 Glastron has Faria gauges and I added one of their depth sounders. No problems except for a tach that had to be hit to get the correct reading. I loosened the "U" bracket that holds it to the dash and it's been fine ever since.
 
I tried a Faria this year. They didn't send the whole transducer assembly with it. Couldn't get anywhere with them, so I returned it and bot a Norcross Hawkeye. Very simple and basic for about $100. Good luck.
 
Thanks for the info guys.

I guess that the Faria rap is to keep getting new ones under warrantee until one of then works properaly. i am doing that now with one of their flow meters.

It was the Hummingbird simple depthfinder that was fastened to the aft part of the hull under the transom that flew off twice in two years at 15 knots. So I give up on that method.

I will check the catalogue for a suitable one.

Thanks,

Joe
 
quote:

Originally posted by JoeShoes

Thanks for the info guys.

It was the Hummingbird simple depthfinder that was fastened to the aft part of the hull under the transom that flew off twice in two years at 15 knots. So I give up on that method.






Yikes! That's not fast at all.

I have a similar type of skimmer transducer on my boat (from Garmin - Airmar, really). It's holding strong after 3 years at speeds up to 30 MPH.
 
quote:

Originally posted by JoeShoes

I guess that the Faria rap is to keep getting new ones under warrantee until one of then works properaly. i am doing that now with one of their flow meters.





No actually, the "Faria Rap" is when you actually have to "rap" the glass of the gauge to get it to work properly. I noticed that my Tach was reading way high, and when I "rapped" it with my knuckle, it settled back down to normal. Something to do with corrosion, I guess.
 
I've got a Hummingbird with a transome mount sender, no problems.
 
My transducer has been attached to the outside of the transom for 17 yrs and has never come lose or stopped working. Even when I had the trim tabs attached, the transducer didn't have to be moved or modified at all.

Perhaps it is a faulty installation or location rather then the type.
 
quote:

Originally posted by blouderback

No actually, the "Faria Rap" is when you actually have to "rap" the glass of the gauge to get it to work properly. I noticed that my Tach was reading way high, and when I "rapped" it with my knuckle, it settled back down to normal. Something to do with corrosion, I guess.





Go back up and read my post about the Faria tach. In my case it could only have been an installation problem. The factory worker installed the mounting bracket too tight. Loosening the bracket cured the problem.

You could also remove and clean all the connectors and reinstall them. And note the position of the switch for the number of cylinders and then run the switch back and forth a few times and then re-set it to the original position.
 
Bob, if your Faria tach has an engine select switch on the back, try changing the little knob away from then back to your correct setting a couple times. Wipes that contact clean. On our Faria, V8 is Position "3" and the little screwdriver slot in the pointer ends up vertical. We have Faria and probably will replace with Faria but I think Teleflex is the better product line.

EDIT: Saw where Ron mentioned jiggering the switch... I did this a few outings ago and it's been fine since.
 
Back
Top