Sinking boat

entilzah

Glad you found it. Let us know the estimates for the repairs. They are boats, hence alot of us are "aware" ouch...of the general costs of these types of repairs. I can't remember if both the motor and out drive have to come out to replace the transom seal...but I think they do...Look hard for any wood deterioration while you are there...that could be a huge deal..
Stan
 
LOL, I'm glad he found it too.
Reading all the posts on his problem, I was beginning to think this was a Test.
Where he knew the problem and was checking us out to see who could lead him to the problem.

Now it looks like somebody may have torqued the throug bolts too much, crushing the transom.
Then seeing what he'd done, backed off on the through bolts a bit. leaving a gap.
 
Probably so Thud...

I always cringe a bit when someones posts "new to me". My "new to me's" have cost $$$$ to get the "new" out

Stan
 
I just checked two different places and they estimate around $2000 to repair, they are completely convinced that if the transom seal is leaking then the wood is rotted. The boat is not worth that much so unless I can figure out how to repair it myself then the boat will bo to the scrapyard.
 
....or you'll sell it cheap to somebody like yourself, and we'll see it again.

Really, if you have the ability to own a boat, you can fix it.

For instance, looking at the whole transome, inside and out, it would only take you a few days to dismantle it.
See what you need, replace it, and .....go use it.

However, My advice, for what that's worth, (it's free) would be to take enough stuff off to see what the problem with the transome really is.
Dont be afraid to take things off. You may see some dirty little secrets that need attention. Fixing them now will result in a good trouble free boat for the future.

You are gonna need an alignment tool for the engine/outdrive alignment.
You'll need some method of lifting the outdrive and maybe even the engine.
The rest is all hand tools and scruitiny!

I can see already that your gonna love boating!
 
quote:

Originally posted by Thudpucker

....or you'll sell it cheap to somebody like yourself, and we'll see it again.

Really, if you have the ability to own a boat, you can fix it.

For instance, looking at the whole transome, inside and out, it would only take you a few days to dismantle it.
See what you need, replace it, and .....go use it.

However, My advice, for what that's worth, (it's free) would be to take enough stuff off to see what the problem with the transome really is.
Dont be afraid to take things off. You may see some dirty little secrets that need attention. Fixing them now will result in a good trouble free boat for the future.

You are gonna need an alignment tool for the engine/outdrive alignment.
You'll need some method of lifting the outdrive and maybe even the engine.
The rest is all hand tools and scruitiny!

I can see already that your gonna love boating!





entilzah

Thud, as usual, is right on the money. I see in your profile that she is a cuddy....you can take the drive off yourself (I have done this and my friends considering me mechanically challenged), Check the extent of the damage and reassess accordingly. If you decide to do this, hollar back and someone will help you screw it up...(just kidding). Part of the love of boating for me, is taking on a new challenge that is differnet than the every day ones we all deal with...sent you my e-mail address….
Stan
 
Thanks for all the help everyone it appears I will start on it this weekend.
 
Because while I am not experienced in boat repair I used to be an ASE certified car and diesel mechanic and am quite sure what a GM 305 looks like. That and the fact that the stickers on the valve covers indicate 5.0 liter which is a 305 GM or a 302 Ford.
 
Install a second bilge pump! Wire it directly to the battery with a inline fuse
 
entilzah

But are you really, really, realy sure [^]

Did you get my e-mail address? Looking forward to seeing what you find. Hell, OK and TX are so close we could be cousins.

chrismbrock

A little late to this thread are we?
 
ESTIMATOR....
My point is that sometime in the future he may need parts or something for that engine and it'll be hard to find parts for it unless he knows what he's got.
Nice link you have there for the GM engines but I'll bet ya that being a 1987 vintage that he doesn't have a Vortec Engine. Therefore.......he doesn't have a 305 with 250hp. The 305 4bbls. used back then were rated at 230hp. and the 350's are rated at 260hp. THAT's my point.
 
Except in the Seloc manual it has my engine in it listed at 250HP. Plus HP rating will not be a big factor in obtaining engine parts.
 
Okay..........I'm gonna let this die out But I'd like to see that. I've been around Boats for a very long time and have yet to ever see a 305 rated at 250 hp. fom back in the 80's. I just went to a Mercruiser website and even THEY have the 305 listed at 220 hp and the 350 at 250 hp
 
LOL Chris and Good Morning!

entilzah,

I tried to upload some pictures of my striper fishing there last year, but the office link is to slow. Great to know you are so close..OKC here and we think we may bring the boat to Texoma once this spring before taking her to Belle Starr on Eufaula for the rest of the season. That was a horrible disaster with Flash Gordon and N. Catz...Stay in touch

Stan
 
Back
Top