Stern heavy?

Grand Larsony

Member
Joined
Jul 29, 2005
RO Number
18485
Messages
155
Have posted this in the Sea Ray form but it doesn't seem to have much traffic...

My 1989 SR 300 DA sits stern-low in the water (as do all of them from what I can tell). This causes water to pool in the rear part of the sink basin, and everything is up or down-hill. Don't like that my berth is not perfectly flat either.

Is it completely stupid to consider loading bags of play sand into the front-most storage area under the berth? We don't need this space, nor do we care about a possible hit on the gas efficiency. We only burn about 40 hours per year and don't go far. I do care, however, about a possible impact to handling and trim.

Would about 300 lbs even make a difference? Would it severely affect handling?

Anyone done tried to fix this common problem before? Had any success?
 
Dock neighbor has a CHB, same problem, same fix, not neg consequences with handling.
 
Have two or three people with known weights sit on the berth and evaluate the change. A couple of 150 pound people are easy to come by and usually are only temporarily there (alot easier to get them to move than bags of play sand). Adding people until you get the bow down to where you want it will give you an idea of how much sand you will need later.

Will the storage area support 300 pounds with out stressing it too much in heavy seas?
 
I have a 20 pound lead block in my forward locker on my center console. It was just enough to keep water from puddling up around the scuppers and getting green algea growing into the cockpit. Doesn't affect the self draining of the boat or the handling capabilities.
 
He he, I can't offer help, but it just reminded me of my last boat. With a full load of people, cooler, etc, it used to be hard to get it up on plane. I would look over at my buddy and give him the look. He would nonchalantly go down below and sit on the forward berth. Sure enough, the boat would pop right up on plane! I would get the "please don't make me go up there" look!

Whatever the case, I think your idea would work fine with no downsides that come to mind.

EDIT: I agree with the others; if there is any way to take advantage of the weight-- like batteries, potable water, large anchor and chain rode <though I would never get a larger anchor than needed>. Once you get the right anchor, it's all about the amount of rode you let out, and how much of that is chain.
 
I had a similar problem with my last boat. My remedy was weight but I used barbell weights. They are round and flat and don't take up much space. Plus, they are easy to move around to adjust distribution as you fine tune it.

Bob
 
If you don't already have all chain, you could add chain to your anchor rode. It would bring your bow down, and you would experience better holding when at anchor. 5/16" chain weighs about 3/4 to 1 lb. per foot. So 100 feet of chain would make up about 100 lbs. of your needed weight.
 
How about some 5 gallon water jugs or one of those water bladders? Alot easier to get out and almost as heavy as sand.
Tim
 
I would make good use of the space and install AGM house batteries.
Bill
 
I removed almost everything from the cuddy including head and cabinets to lose weight. Trouble is I stripped the cockpit and built up the cockpit for more fish holding capacity. Really ended up with a stern heavy boat. Started with moving the batteries from the stern to the cuddy and adding another battery. That alone was pretty close to moving 300 lbs forward. Moved all my tools forward which came to the equilivent for 400 lbs forward. The stern sits 2" higher.

Like Paul said, redistribute what you have. every 100 lbs you move from the stern to the bow is doubled.
 
Charlie,

You moved all the batteries? I was thinking of planting a couple of batteries for the house forward, did you use #8 cable? I assume you would need closer to #4 or at least #6 if you were starting the engines from them correct?
 
Don,
I had some brand new really heavy duty welding cables laying around doing nothing. I did my best to protect the cable end fittings with plenty of di-electric silicone grease(I buy it by the 5 oz tube now). They have no problem carrying 200+ amps.
 
quote:

Originally posted by Bluedog

How about some 5 gallon water jugs or one of those water bladders? Alot easier to get out and almost as heavy as sand.
Tim






I agree....to a point! I'd fill the jugs or bladders with beer, moonshine or drink of choice! Maybe even the mixer! Would work awesome...until it was all gone...but by then....you won't care if yer boat is stern heavy, bow heavy or 3' lower in the water!!!!!!!
 
Redistribution of weight is the way I did it. Worked fine without adding to the weight of the boat.

After I added the trim tabs, I didn't need to have someone go forward to get the boat on plane. My guests are much more comfortable now!
 
So far it seems the best solution and least expensive solution is to add weight to the bow. It would be great to move something heavy from the stern to the bow. I don't see moving anything as a simple thing; including buying new AGM batteries. Get an idea as to how much additional bow weight is needed to level out the boat for your satisfaction. Then decide whether you just want some sand bags to correct the issue.
 
Just make sure that what ever is placed up front is firmly secured. A bouncing weight can punch a nasty hole in the boat.
 
Back
Top