Stuck Plug

Scotttyd

Member
exMember
Joined
May 28, 2007
RO Number
26481
Messages
45
Ok, I took my new boat (new to me, but gently loved as the Saturn people say) out for the first time. I went to take the plug out and it was stuck, I could not even budge it, am I stupid or is something wrong? It is a glastron bowrider, I took a 9/16 wrench and could not even slightly budger it, I am not a small guy so it is not just I am a total weakling. Any advice?
 
Humm, spray some penetrating oil on it then put a box wrench on it and and an extension to the wrench, cross your fingers and pull away... [^]
 
Suggest a slow approach!

If what you have is a "garboard drain" the Brute Force approach can cause you problems. Garboard Drain is a brass flange, sealed with compound to the transom and held in place with probably three screws. Then a threaded brass plug, correct? What can happen is that you'll wrench the screws and the compound loose and that can lead to water soaking into the transom core. The fix for that is a minor hull repair.

No guarantees, but apply the solvent [to BOTH sides if you can] as Ron suggests and let it soak. Then put the wrench on it with moderate force and try tapping on the side of the wrench while the force is on it. If it starts to loosen then balks, apply more penetrant and go toward tightening just a tad. Get to where you can work it both ways, gradually you can work it toward loose and out. Then install and remove it often and you should be fine. And get a spare plug, too!
 
j-d, do those kind of plugs require a lubricant when installing? I'm only familiar with the tried and true brass plug which I grease prior to reinstalling each time........
 
Gee, Flutter, I don't really know. I take ours out every time I put it up on the boatlift. Concerned enough Florida Liquid Sunshine will get in there to make the boat awful heavy or flood the starter etc.
Anyhow, I take it out often but enough sand and grit come out with the bilge water that I don't want it getting stuck in grease. Now if I were planning to put it in there and leave for a couple months in saltwater, I think I'd grease it, or try Teflon tape or Teflon Plumber's Grease. As I recall, you moor on an airdock and that probably means you leave the plug in, so I'd be two for grease.
Hope you had a great Fourth!
 
My advice is, if you are new to plumbing, ask for assistance. A 9/16" wrench might simply be too small. Consider using a small pipe wrench but be careful, you don't want to damage the plate as stated above....that's where the assistance/experience comes in. Knowing how much pressure is too much could save you headaches. Assuming it's brass on brass, you should be OK, no matter what. However, someone might have thrown say a cast iron plug in the brass plate and dissimilar medals can corrode quire a bit.

When it's all said and done, make sure you use teflon tape to re-insert the plug. Not only does this help with a nice water tight seal but it also helps when it's time to remove the plug. It's cheap and easy insurance....good luck!
 
j-d, thanks! Yes, I leave the plug in. I'm in a covered slip, so do not worry about rain collecting while I'm gone. But when I rotate my prop, I also remove and reinsert the plug so it doesn't get locked in. It is simple to do and I hope that prevents future problems. At 16 yrs, the old girl isn't as she used to be and little problems tend to crop up more frequently now. I grease the plug with the same grease I use on the prop.

My Fourth was very safe and quiet.....I stayed home!
 
"When you "Rotate" your prop???"
What exactly do you mean there?
 
I have two props for my single I/O. Once a year I remove the prop and replace it with the spare, second prop. I send the other out to be tested and balanced and that becomes my spare for the following year. I remove, grease and reinstall my plug at the same time.
 
Gee, Flutter, I thought you were just a couple years older than 16...

Grease like you're doing, or Teflon Tape, sounds like the winner. Two Dings for Teflon Tape.

We patrolled the downtown fireworks display. Wound up towing a 37' that got the anchor line around both props and probably at least one rudder, "we have a spare anchor but no line for it"... We were pretty close to one of the three barges when the show went off. Let's say the view was straight up.
 
"And the spare anchor is for......what purpose?" Hard to understand how one can afford a 37' boat and not know the basics!!! Yikes. Glad you had an unobstructed view!
 
Thanks all, a little WD 40, 3 minutes, and my two year old nephew could have pulled that plug out. Although not a drop of water came out, what is the need (just joking I know there a reason for it). I love this forum, I can ask a question that may seem very simple, yet my only worry is someone will make fun of me online, which I think is even more pathetic than someone asking a stupid question. Like I always tell my coworkers, there is no such things as a stupid question, just stupid people who ask questions.
 
Did you re-insert after wrapping with some teflon tape? Don't overtighten, no need to.
 
Scotty, the stupid people do not ask questions on this forum. Unfortunately.
 
Back
Top