Using 5200 Adhesive?

Dauphan

Member
exMember
Joined
Oct 18, 2004
RO Number
15551
Messages
51
This may be an odd question, but does anyone have a technique for using 5200 adhesive? I'm trying to glue back some plastic molding that popped loose on the side of my boat. I'd hate to make a mess but 5200 seems to be very runny and I'm wondering if there is a good way to apply it on the side. The molding is partly attached at the back but is sticking out in the front. Is there a good way to hold it in place for 48 hours so it will stay stuck? Sorry for the fragmented question, but I appreciate the help.
 
maybe some of that blue painters tape? i've used that with some good results to hold something long enough until the glue sets
 
5200 is not an adhesive, it just happens to work for most useages, it's a caulk that sticks real well. Maybe some 5 minute epoxy would work better.
 
Actually 5200 is an adhesive and sealer

"This high-performance polyurethane adhesive/sealant becomes tack free in 48 hours, completely cures in 5-7 days with no shrinkage."

Just be sure you do not want to separate what you put together.
 
I've used 4200 and not found it to be runny, and it has the potential advantage of being (supposedly) removable.
 
5200 is THE ADHESIVE. I learned that the hard way 15+ years ago when I used it as a sealant and later wanted to remove the hardware.
 
Only for those seeking a permanent relationship.
 
Smallbore piano wire or monofilament (that kevlar braided fishing line works AWESOME) is the trick to remving 5200. Doesn't break the adhesion, but cuts through. Then it's razor blade and acetone time. And band-aids. Gonna need band-aids.
 
Um, ok. So tape should be enough to hold the surfaces together long enough for the adhesive to set. I want this to be permanent, which is why I got 5200. So, how do I apply the stuff and how thick or even to I have to apply it? Is just wiping on with a spatula / putty knife enough? Thanks.
 
It does not take much. one quarter inch bead in the center, then dont over tighten to the point of squeezing the 5200 out.It will be permanent I promise....Jerry
 
The Fast Cure 5200 or 4200 is tack free in one hour and cures in 24 hours. I can't find anything that says that the final result is any different between the fast cure versus regular.
 
The diffrence between 5200 and 4200 is the bond.5200 is considered permanent.4200 is temporary,although not by much less.Both are rated above and below water line usage.5200 will peel whatever it's attached to while 4200 will detach without damage most times.I know I have extensive experence with both owing a wood boat. Jerry
 
the best adheasive i have ever found is "the right stuff" buy permatex it will stick to almost any surface and if you wet your finger you can smooth it to a polished finish its the only silicone we use on any engine as it dries to a tough firm urathane like rubber but it only comes in small calk tubes and only in black.....
 
I'll stick by my statement, 5200 is a sealant fist (caulk), also works and very well I might add, as an adhesive it alot of cases. A good adhesive sets up relatively fast, not days. I've used liquid nail on the boat for low load, low vibration applications. It will hold relatively fast (with-in minutes) and cures over night.
 
What kind of plastic? Even 5200 won't permanently stick to starboard or similar surfaces.

bp
 
Jim P ... I guess perhaps the 3M company needs to change the advertising of 5200 from adhesive/sealer to sealer/adhesive. It works equally well as both.
 
Thanks for your help. I'll give it a try and see what happens. I don't know what kind of plastic this is, but it's cheap plastic in which the retainers fell off after just a few months of use. Unfortunately the area is subject to vibration and water. 5200 should be good for an area like that. Thanks again.
 
I was going to use 5200 to install the Transom mounted transducer on my fish finder, till reading this. I was going to use it for the screws and to fill the whole in the transom. It sounds like 4200 would be better, or maybe something else?

If anyone has any recommendation let it fly!
 
Back
Top