Why displacement?

HarlenW

Member
Member
Joined
Mar 30, 2007
RO Number
25699
Messages
473
Its heavy mystery time (with apologies to George Carlin):

As I understand it, a boat's displacement is the weight of the water it displaces while afloat and is equivalent to the actual weight of the boat.

So why isn't it just called the weight of the boat?
 
WHere does it say that it's equivalent to the wt of the boat? Also, the volume of water displaced varies depending on if it's salt water or fresh water. More to think about. I'm confused now!
 
Harlen, you had it right in your first post. In terms of physics, the "weight" of any buoyant vessel is equal to the weight of the volume of water it displaces. Freshwater, saltwater - it doesn't matter. A vessel in saltwater will displace less water (volume-wise) than the same vessel in freshwater, but since the saltwater is denser, the weight of the volume displaced is a constant (that constant being the actual weight of the vessel at that time). This variance in the volume of water displaced effects the draft of a vessel. Hence the reason for load lines (Plimsoll marks) on ships.

What Pascoe is saying is that the specified weight of a boat used by most manufacturers is a dry weight of a vessel without fluids, provisions, gear, crew etc. This number is most certainly different (lighter) from when the vessel is in an operating status, loaded with fuel, a crew etc. This number may not also reflect the stated displacement of the boat.

Displacement as a given number is based off of a formula used by naval architects and may not be the actual physical displacement, since this is not practical to actually measure.
 
Then there are the rare boats that weigh more than the water they displace. These make fine dive sites & fish habitats.
 
I remember hearing once that "displacement" had to do with the amount of cargo a ship could carry. Here's something I looked up:

"The tonnage of a ship is not a weight, but a volume. One ton is 100 cubic feet. The
total internal volume of a ship is its gross tonnage, and if we subtract all the volume not used for cargo, we get the net tonnage."
 
The word tonnage coincidently begins with the word "ton", despite that it has nothing to do with weight. There are different types of tonnages.

Gross tonnage is a measure of the total internal volume of the ship. This is essentially the "size" of the vessel and is what is used for USCG licensing purposes.

Net tonnage is essentially the volume of the cargo stowage areas (ie: gross tons, minus accommodation and machinery spaces, non-cargo tanks).

Now for weights:

Displacement is the actual weight of the vessel at any time. The rated displacement of a specific vessel is based on a formula and on ships, is usually the calculated displacement when the vessel is loaded to what's known as its full load summer draft.

The lightship weight is also given. This is the weight of the ship without fuel, cargo, stores, crew etc. The difference between the maximum rated displacement and lightship weight is the deadweight tons (DWT) capacity, or how much cargo, fuel, water and stores the vessel can carry safely and legally. You often see tank vessels rated and categorized by by their DWT (handy, medium, VLCC, ULCC).

There are also displacement tables on the ship that when the draft of the vessel along with the density of the water is entered, the displacement and deadweight of the vessel is given (or, vice-versa). These numbers are important for stability calculations and ballast considerations.

All of these tonnages and weights are applied at different times for fees, licensing, pilotage and other legal/commercial requirements.

I hope that's not too confusing.
 
KPMID you just convinced me that I'm well beyond my learning curve!
 
Wow! I never knew how much I didn't know......
 
additionally, the amount of water a hull displaces is proportional to its height ratio. a measured volume that is shallow will displace more then that same if it was vertical. that is partially the reason that deep draft ships do not lower at the same rate as the weight of cargo is added. water pressure changes the density as you go deeper.
 
Whatever you were smoking when you thought that one up, I want some!!!
 
Actually Don B is correct -- that's how submarines can maintain a depth. However the bulk modulus of water is a very large umber and it takes a corresponding large change in depth to develop the pressure to significantly change the density of water.
 
Back
Top