Why so few bow pulpits these days?

AustinPaul

Active member
Member
Joined
May 12, 2005
RO Number
17353
Messages
1,267
Why do you think it is that builders rarely build pulpits into their designs? Is it just a style thing? Is there a practical benefit to NOT having one?

I've always liked them from a practical standpoint (like have the anchor out there where I can get to it to clean, etc.) and I've always liked them from a styling persecptive-- I just think they add to a boat's nautical look.

Paul
 
i coudlnt' agree more and i have never been able to figure that one out either.

I would NEVER own a boat without a bow pulpit, unless maybe the anchor roller is built in the bow under the rub rail, as you see on larger vessels. But a flimsy anchor roller sticking out, simply doens't cut it in my opinion.

in addition to the lack of pulpit, many builders extend the bow rail beyond the hull which makes it even worst... Then they sometimes take it further up the impractical scale by leaving no flat surface to stand on...

my favorite is an integral pulpit like i had on my previous boat. if need be, i could pivot the boat against a piling when pinned by the wind. didn't have to worry about anything, the pulpit was integral with the rub rail going around it.
 
I'd rather see boats designed to retain anchoring functions without the bow pulpit. At a covered slip, you'll pay more for a longer slip every month you own a boat with a pulpit.
 
quote:

Originally posted by PascalG

I would NEVER own a boat without a bow pulpit, unless maybe the anchor roller is built in the bow under the rub rail, as you see on larger vessels.






Sorta Like this Pascal? A bit hard to see in the picture but it is below the rub rail. Anchor shank actually goes into the boat.

bowline9-29-30+001.jpg


Just curious what you think.
 
my thought is hard to explain and defend while typing but.... if you integrate the anchor assembly in to the hull you can now call it a larger boat and sell it as a larger boat.

my boat titled as a 32'9" boat. as it sits w/o the pulpit and platform. now you add the pulpit and you have a 34'6" boat. integrate the pulpit into the same length hull and you are selling a 34 or 35' boat.

i feel the same way about swim platforms.

of course there is always the train of thought that it just looks cleaner
 
It's an European thing. LOA is LOA and LOA costs dearly in Europe to berth. The anchor roller cuts down on LOA. some of the boats had the Harry Schoell designed anchor that is actually an integral portion of the hull. I have only seen one since I returned to the states in 1991. It was not uncommon to see hinged swim platforms as well. That was then and I have not been back to Europe since 1991.
 
rommer,

yes...that's much better in my opinion than the roller extending above the deck like on the boat on the left side of the pics. I guess it's a good compromise as long as the railing does extend too far. I've see boats where there is actually a space between the lower railing and the edge of the bow, not safe but in calm waters.

personally, I dont' care much boat LOA, it's a game that builders play and you can't be sure what it means. what matters is comparing actual space available... my old maxum was called a maxum 37 but the LOA was 39, because of the pulpit or integral platform i assume.

i think that what they call it isn't too important... the pulpit shoudln't be included in the marketing numbers...

i also find a pulpit practical to stand on to see what's going on with the anchor, get a good pull if needeed, rinse it, etc... but the more i see the under rub rail setup the more i like it.

btw, i see many boats around here with bent rollers...
 
Regardless of how boat length is measured, a marina is going to get into trouble with the fire marshal if they let bow pulpits hang over a walkway. Don't know how many times I've seen boats with pulpits moved to larger and more expensive slips because of this.
 
I love bow pulpits. I really want to see them come back. Its just the best design for handling anchors. Not to mention that it makes boats look more like boats. :-)

I would rather a bow roller than hull integration below the rubrail. Everyone I have seen had a hole in the bow, and I'm just not comfortable with that. Also, I don't see how one can safely remove debris from the anchor if its well out of the way like that. I have enough trouble removing 100lbs of weeds on my anchor, and I have a pulpit.

Shel
 
I'm confused on this one. When I want to clean off an anchor, having a pulpit OVER the anchor hasn't made it easier for me. I have found it much easier to work with the anchor when it's hanging directly from the roller.

I think the integrated look is nice, but it gives the operator the LEAST amount of access to the tackle.

I agree that pulpits give a boat a nice look while offereing protection and a pivot point.
 
Here is a drawing of the topsides of our boat.

3880%5Fplan%5FDeck%2Ejpg


The 2 side compartments each go down into the anchor rode locker as well as having a shelve to hold a fender and a line holder. The center compartment about 12" wide by almost 3 feet long gives you full access to the anchor tackle and windlass.

Here's a video that shows the area. http://www.regalboats.com/video/B4080_77_300k.mov

My only complaint is the 2 gas shocks are not strong enough to hold the center locker open in the wind and I have been beaned in the head.
 
quote:

Originally posted by yzer

Regardless of how boat length is measured, a marina is going to get into trouble with the fire marshal if they let bow pulpits hang over a walkway. Don't know how many times I've seen boats with pulpits moved to larger and more expensive slips because of this.







Simple solution -> pointy part out, flat part against dock. In other words, stern in.
 
quote:

Originally posted by SLW

I'm confused on this one. When I want to clean off an anchor, having a pulpit OVER the anchor hasn't made it easier for me. I have found it much easier to work with the anchor when it's hanging directly from the roller.






Not always the case. I have fresh water wash down. I stand on the pulpit and wash through the opening down the middle of the pulpit to wash the top of the anchor. I can get the bottom as the anchor is retrieved. It's really very simple.
 
Opening doors when it's integrated, and shooting water through the opening of a pulpit vs. the anchor in plain view, deck level?

A lack of a pulpit has drawbacks, but I still maintain that it offers the best access.
 
quote:

Originally posted by HOGAN

quote:

Originally posted by yzer

Regardless of how boat length is measured, a marina is going to get into trouble with the fire marshal if they let bow pulpits hang over a walkway. Don't know how many times I've seen boats with pulpits moved to larger and more expensive slips because of this.







Simple solution -> pointy part out, flat part against dock. In other words, stern in.









It's not only a simple partial solution (the V-section at the front of the slip is still wasted), but at our marina on the San Joaquin River, it's a mark of good boat handling abilities.
 
Most aftermarket and even factory add-ons that I've seen were poorly designed and even more poorly mounted. My bow rail will hold at least 700lbs and the pulpit will hold over 1000lbs
 
quote:

Originally posted by yzer

quote:

Originally posted by HOGAN

quote:

Originally posted by yzer

Regardless of how boat length is measured, a marina is going to get into trouble with the fire marshal if they let bow pulpits hang over a walkway. Don't know how many times I've seen boats with pulpits moved to larger and more expensive slips because of this.







Simple solution -> pointy part out, flat part against dock. In other words, stern in.









It's not only a simple partial solution (the V-section at the front of the slip is still wasted), but at our marina on the San Joaquin River, it's a mark of good boat handling abilities.








At the new slip where I'm headed, we're planning to slip the boat bow-in, as we will have an unobstructed view of the lake and sunsets from the cockpit. Yes, it's going to make boarding tougher, but it's worth it for the view and the privacy.
 
I like to berth bow-in for the same reason. While at the marina I spend most of my time in the cockpit, looking out to the view away from the marina building. There are some more sociable boaters at the marina who like to berth stern-in, though.
 
Our boat has a bow pulpit, despite many builders of similar designs opt to forgo the bow pulpit in keeping with the traditional lines of the 'deadrise' hull. In fact, our builder has the same model boat, without a bow pulpit. Personally, I like the appearance and functionality of a bow pulpit.

I guess you can sum it up as personal preference!
 
quote:

Originally posted by yzer

I like to berth bow-in for the same reason. While at the marina I spend most of my time in the cockpit, looking out to the view away from the marina building. There are some more sociable boaters at the marina who like to berth stern-in, though.




Actually, we're one of the social ones. At our current slip (36'x14') we also have a 14'x8' deck the rear of the slip. We have party lights, a grill, and layout our rug, along with chairs and a table. We're going to miss that setup, but will make up for it with the bigger boat. Somehow, being located adjacted to a bar/grill/restaurant, I think we'll manage to have a good social life. BUT, there are those times where we just want to be left alone and be quiet--that's the advantage I see to being berthed bow-in. Hey, we can always turn the boat around when needed!

Paul
 
Back
Top