Antenna mount?

32carv

Well-known member
Member
Joined
Nov 4, 2006
RO Number
24150
Messages
1,309
I am going to purchase a Shakespeare 2030-G TV Antenna for my Carver 3227. My problem is that I don't have a radar arch and am looking for a place to mount it on the flybridge. Any ideas? Pictures would help.
 
http://www.supermotors.net/getfile/510403/fullsize/boat.jpg[/img]]

100_2137.jpg


img_0539.jpg
[/img]
 
if its the type of TV antenna that looks a bit like an overgrown frisbee, you can mount it on a standard 6 or 8 foot extension from the sides of the flybridge.
 
32, here you go:

carver.jpg


Yep, do what Vic said
 
yep, get an 8' extension, mount it on the side of the flybridge and put the antenna on top. Where is your anchor light? usually on archless flybdige boats you can use the same extension for both.
 
The anchor light is inside of the bridge enclosure. The antenna that I am looking is a disk about 21 inches wide and 1 inch thick. I thought of the 8 foot mast but I was afraid that it would move too much and not be enough while underway.
 
inside the enclosure? not ideal.. you may want to move it on the extension while you're at it.

mount the base of the extension a little low, along the flybridge, and add an antenna brace 18" above the mount. that will make it more rigid.
 
Thanks, sounds like the best way to mount it is using the mast and brace. I measured today and a 6 foot mast should get over the top of the enclosure. The mounts that I see are either stainless or plastic. I think I already know the answer but does anyone know if the plastic mounts are strong enough to support this?
 
with the brace it should be... but is it worth taking a chance? :-)
 
Does anyone know if I will need a converter box with this antenna? It says that is "HD ready".
 
The HD issue is whether your TV is HD/DTV ready. If it is, no box. If it isn't, then yes, a box.
 
TV is not but I plan to buy a new one so will be OK.
 
quote:

Originally posted by 32carv

Does anyone know if I will need a converter box with this antenna? It says that is "HD ready".





They all say that. It's a gimmick. An antenna knows nothing about the signal it is receiving as long as it's in the frequency range the antenna is designed for. If it's a VHF/UHF antenna (and just about any antenna manufactured in the past twenty years is), it will be fine.

The important thing is to be sure you use an "omnidirectional" (picks up in all directions) antenna for a boat. Unlike your land based home, boats move and you wouldn't want to have to rotate an antenna every time your boat moves.
 
dont worry about the underway reception, you'll be busy on the bridge. if you truely want clear underway reception for the crew you'll need a sat antenna that is motion stabilized. there are some newer generation products that are fairly light, but not light enough to put on an antenna extension, you wuold need an arch of some kind. pascal raises a good point about the anchor light, it should be clear of obstructions 365 degrees around the boat from all angles horizontaly so even if the boat is rolling a bit anyone can see you from any elevation.
 
I never thought about it but what you are saying about the anchor light makes sense. It is original equipment and has not been modified so it is obviously a design flaw by Carver. I will look for options as I'm buying stuff for the antenna project.
 
I just did this install on my 3607AC last year. I'll give this a best shot at verbally describing since the boat is in storage (no pics - forgive the length).

Last winter had the canvas shop sew in a round boot on the underside of my canopy (like yours) adjacent to the canopy support sleeve. The boot has a circumferential zipper around 180 degrees with the end of the zipper positioned next to the support sleeve. I had them place an eyelet in the sleeve large enough to put a coax fitting through. Then I slid the antenna into the boot, closed the zipper snug up to the cable, ran the coax inside the support eyelet (exposes only 1" of coax to the eye), down the support rod (later covered with a wrap to hide it), ducking into the access hole next to the helm. From there I have a wiring access route down to the lower helm, ducking into the engine room, running diagonally across to the coax outlet. Works great!
 
quote:

Originally posted by vic33004

dont worry about the underway reception, you'll be busy on the bridge. .......





If this is a reply to my comment about the boat moving, I'm not talking about underway, I'm talking about at anchor or in a marina away from home.

In my area, the anchored boat swings with the tidal current and/or wind. Re-aiming a TV antenna would be a real PITA.
 
Back
Top