Electro guard

No mercathode is not intelligent...this device looks like it can adjust based on conditions, etc.

Wow, if it works...the BIII might once again be a good choice.
 
Incorrect. A mercathode works the same way as this device does. Both use a silver reference electrode, both have an anode thus both units adjust based on conditions. The question is what is the output wattage of this unit versus the mercathode. Some mercathodes are inadequate for what they have to protect. However that can be remedied by adding additional units in parallel to the same reference unit. If you have a black unit, and need more output, step up to a blue unit or even more a red unit. Then you can start paralleling units.

Before I would buy this unit, I would call the mfr and ask what the maximum output of the unit is. My guess is it is a higher output than a mercathode. Personally it is cheaper just to parallel in another mercathode box and you got the same thing.
 
Thanks for the correction...then what I still do not get is why does the mercathode not work for ALL BIII Drives...you have to get the perfect balance with number of mercathode units, blue, black, vs hull potential.

Does the mercathode really have the ability to adapt to changing conditions...I really don't think so...if so, why all the corrosion issues?

Are you saying if you have two blue units in parallel, and it does not need all the output wattage, the merchathode will cut the power? If so then why not just put three merchathodes wired together for max protection...and it will adjust itself down?

As you can tell, I have a set of 2008 BIII's in fresh water, with less than 6 months touching water and they are already showing solid signs of corrossion...and yes I've done all the right things, except add multiple mercathodes, as the Merc tech said no way.
 
I had 2001 B3's with no corrosion.
I bought a 2nd mercathode for each so I had 4 mercathodes for 2 engines.
I checked them occasionally.
I also bought an electrode and checked the output of them in the water.
I also added the prop zinc anode.
I also made sure I used the correct zincs for my water and checked them often.
I also painted my drives with trilux.
I had no corrosion issues.
B3's are great but require some work.
If your 2008's are already showing signs of corrosion then I question how much of above you are doing.
Make sure your mecathodes are working, they have fuses that can blow.
Make sure they are wired direct to battery.
Make sure your zincs are the right ones and if they are not doing their job, dump them and get different ones.
Not all zincs are created equal.
Make sure you have a galvonic isoloater installed.
Look at your neighbors boats. Do they have wires hanging in the water?
 
CurrentSea,

Everything but 4 merchathodes...maybe that is the trick?

Of course I did not paint with Trilux either...

So what I was looking for was that the extra Merchathodes do not "over protect"...which it is looking like it might not?
 
They can't over protect.
Get yourself a volt meter with an electrode.
I may sell mine since I sold my boat.
Test your protection it will always be between 750mv and 1000mv no matter how many mercathodes.
You need trilux on the drives.
Pull them and paint them.
They won't look pretty, but they will be better protected.
Merc factory paint is the worst!

I can send you some info on how to test the mercathode and how to wire in a another one.
 
Man that would be great...I was told mine tested ok, but better to see with my own eyes.

Let me know if you just want to post how to test and how to wire a secondary...or if you want to email, guess I could provide my email address via a PM to you I think.
 
I emailed you the info and I will post here. I can't post the diagram of how to wire the mercathode.
This comes to us originally from GeeBee:

In saltwater, use the genuine Mercruiser Aluminum anodes. In freshwater use Magnesium
Make sure you do a hull potential check as outlined in your service manual at least once a month. Keep a log.
It cannot hurt to put on a second mercathode.
It cannot hurt to add additional mercathode anodes (those little pucks on the transom)
It cannot hurt to hang an additional zinc (grouper type) behind the prop when she is in the slip. Use a magnesium grouper in fresh.
Many people think you can "overprotect". This is true on inboard boats, but you got 200 pounds of aluminum outdrive hanging out there. It is impossible to put to much protection for a sterndrive.
Make sure you keep the prop shaft liberally lubricated with 101. It will cut down on the activity between the props and the drive
Keep the aluminum on your drive well painted, it insulates the aluminum from the stainless props.

In general, the best indicator that your protection is holding up is hull potential. When your "zincs" start to get weak or inactive a drop in hull potential will be your indicator. You cannot tell by visual inspection of the zincs, as they will go inactive before they wear away. Make sure you keep your hull potential in the upper range.

The issue with the BravoIII is they did not put enough anode material on it. Indeed in terms of mass of anodes, the BIII has less than the BII despite having twice the amount of stainless steel cooking with the cast aluminum drive. They corrected this on post 2002 models.

For the hull potential get the Mercruiser probe from Boatfix, it's about 90 bucks.

Try this http://www.boatfix.com/bykeywordmerc.asp?textfield=76675&texttype=2&submit=Search. Should bring it up for you, part# 91-76675T 1.

Use your own VOM of course. If you use the meter from Radio Shack on auto range it should read above .650 which equal 650 millivolts. If it goes above 1000 milivolts then it will read 1.000 or above. If you are in the low 700's you are underprotected. I usually look for numbers in the high 8's low 9's except when the anodes are brand new, then I can get above 1000.

Get an autoranging VOM from Radio Shack, they have a good one for about 50 bucks. It has to read volts to 1/1000 of a volt, which is 1 millivolt. Follow the instruction in the Mercruiser service manual. It is the best way and indeed the only way to tell that your anode protection is breaking down.

As for the pucks, if you have corrosion problems you should consider installing two of them, one on each side of the drive. Just hook them up to the Orange terminal on the Mercathode unit.

The grouper anode needs to be connected to ground on your drive. If you can thread it into your engine compartment and clip it one of the through bolts that holds the gimbal unit on, that works

1 millivolt equals 1/1000 of a volt. Thus 1000 millivolts is 1.0 volts.

METER SET UP.

Now, let's look at your meter. Make sure the black wire is in the black recepticle, and the red wire from the probe is in the red receptacle The one that says "volts" NOT AMPS). Next select "V" on your meter. It's one click clockwise from "OFF". Now make sure that ~ is not displayed on the left hand side of your display. If it is, press the "SELECT" button to blank it.
Next make sure "AUTO" is displayed on the meter. If not, press the "RANGE" button until it does.

HULL POTENTIAL TEST

Now place the black probe to a ground point on your drive, or use the battery negative. Next dangle the probe at prop level, about 6 inches behind the prop. You should read between .750 and 1.1 which equals 750 to 1100 milivolts.
Lower than .750 you are underprotected.

MERCATHODE TEST

To verify your Mercathode output, set up the meter as above, except use the "red" probe that came with the meter, not the silver chloride probe you dangle in the water. Put the black wire on the "-" of the controller and the red wire on the "A" post (orange wire). You should read around 12 volts. To verify the Mercathode reference electrode, put the black probe on the "-" post and the red probe on the "R" post (brown wire). It should read about the same millivolts as your hull potentetial test.
 
Back
Top