I emailed you the info and I will post here. I can't post the diagram of how to wire the mercathode.
This comes to us originally from GeeBee:
In saltwater, use the genuine Mercruiser Aluminum anodes. In freshwater use Magnesium
Make sure you do a hull potential check as outlined in your service manual at least once a month. Keep a log.
It cannot hurt to put on a second mercathode.
It cannot hurt to add additional mercathode anodes (those little pucks on the transom)
It cannot hurt to hang an additional zinc (grouper type) behind the prop when she is in the slip. Use a magnesium grouper in fresh.
Many people think you can "overprotect". This is true on inboard boats, but you got 200 pounds of aluminum outdrive hanging out there. It is impossible to put to much protection for a sterndrive.
Make sure you keep the prop shaft liberally lubricated with 101. It will cut down on the activity between the props and the drive
Keep the aluminum on your drive well painted, it insulates the aluminum from the stainless props.
In general, the best indicator that your protection is holding up is hull potential. When your "zincs" start to get weak or inactive a drop in hull potential will be your indicator. You cannot tell by visual inspection of the zincs, as they will go inactive before they wear away. Make sure you keep your hull potential in the upper range.
The issue with the BravoIII is they did not put enough anode material on it. Indeed in terms of mass of anodes, the BIII has less than the BII despite having twice the amount of stainless steel cooking with the cast aluminum drive. They corrected this on post 2002 models.
For the hull potential get the Mercruiser probe from Boatfix, it's about 90 bucks.
Try this
http://www.boatfix.com/bykeywordmerc.asp?textfield=76675&texttype=2&submit=Search. Should bring it up for you, part# 91-76675T 1.
Use your own VOM of course. If you use the meter from Radio Shack on auto range it should read above .650 which equal 650 millivolts. If it goes above 1000 milivolts then it will read 1.000 or above. If you are in the low 700's you are underprotected. I usually look for numbers in the high 8's low 9's except when the anodes are brand new, then I can get above 1000.
Get an autoranging VOM from Radio Shack, they have a good one for about 50 bucks. It has to read volts to 1/1000 of a volt, which is 1 millivolt. Follow the instruction in the Mercruiser service manual. It is the best way and indeed the only way to tell that your anode protection is breaking down.
As for the pucks, if you have corrosion problems you should consider installing two of them, one on each side of the drive. Just hook them up to the Orange terminal on the Mercathode unit.
The grouper anode needs to be connected to ground on your drive. If you can thread it into your engine compartment and clip it one of the through bolts that holds the gimbal unit on, that works
1 millivolt equals 1/1000 of a volt. Thus 1000 millivolts is 1.0 volts.
METER SET UP.
Now, let's look at your meter. Make sure the black wire is in the black recepticle, and the red wire from the probe is in the red receptacle The one that says "volts" NOT AMPS). Next select "V" on your meter. It's one click clockwise from "OFF". Now make sure that ~ is not displayed on the left hand side of your display. If it is, press the "SELECT" button to blank it.
Next make sure "AUTO" is displayed on the meter. If not, press the "RANGE" button until it does.
HULL POTENTIAL TEST
Now place the black probe to a ground point on your drive, or use the battery negative. Next dangle the probe at prop level, about 6 inches behind the prop. You should read between .750 and 1.1 which equals 750 to 1100 milivolts.
Lower than .750 you are underprotected.
MERCATHODE TEST
To verify your Mercathode output, set up the meter as above, except use the "red" probe that came with the meter, not the silver chloride probe you dangle in the water. Put the black wire on the "-" of the controller and the red wire on the "A" post (orange wire). You should read around 12 volts. To verify the Mercathode reference electrode, put the black probe on the "-" post and the red probe on the "R" post (brown wire). It should read about the same millivolts as your hull potentetial test.