Windlass project

32carv

Well-known member
Member
Joined
Nov 4, 2006
RO Number
24150
Messages
1,309
This winter I am thinking about adding a windlass to my Carver 3227. I can handle the project but don't know anything about windlasses. I searched this forum and other websites but as usual got much conflicting information and opinions. What are the most important factors when selecting a windlass?
 
I installed a windlass this past spring on our 28 carver. We went with a lewmar. The entire unit is SS (so it looks quite nice) and it sits above deck (there was not alot of room in the anchor locker for the type which mounts below deck). Some of the lessons I'd pass along from my experience would be:
-after cutting holes through the deck, epoxy the edges of the cuts to prevent water from getting at the core.
-ensure you use the right size wire (windlasses draw huge current)
-make sure the windlass you choose handles the appropriate size of line and chain your boat requires.
-expect the running of cables/electrial part of the job to take much longer than the installation of the windlass itself
-follow the wiring instructions carefully and use the right size breaker.
-expect the admiral to be truly grateful...and take advantage of it...;)

I'm sure others will have lots of other advice....good luck. It was a great addition ot our boat eliminating much of the stress of anchoring which my wife truly appreciates. She actually said, and I quote: "it's the best thing you ever bought for the boat.....now we have an anchor winch , I dont have to be an anchor wench". Whats better than a happy admiral?
 
I looked at Lewmar and they appear to be of pretty good value for the money. The 700 series would be the size for my boat but I am considering oversizing and going with the 1000 series. Is that worth doing? Also, what are the advantages or disadvantages of the vertical vs. horizontal windlasses?
 
I've had a Lewmar 1000 free-fall model for a couple years now... and it's now hard to imagine how I got along without it! With the windlass I can handle more chain and a larger anchor than I could before.

My only complaint is it doesn't have a rope drum.
 
A vertical windlass is usually more attractive since it has a lower porfile and hides the rode as it travels through it. The rode makes a roughly 180 degree trip around the gypsy then makes a 90 degree turn in a different plane to go through the deck. A deep anchor locker is a plus with this type of windlass since the weight of the rode is what is what is pulling it into the locker.

A horizontal windlass usually sits higher off the deck and can be a "tripper". The gypsy is also usually exposed. The rode makes roughly a 90 degree trip around the gypsy before being pushed into the anchor locker. If your anchor locker is shallow a horizontal windlass might be a better choice.

Good luck!
 
A vertical windlass is usually more attractive since it has a lower porfile and hides the rode as it travels through it. The rode makes a roughly 180 degree trip around the gypsy then makes a 90 degree turn in a different plane to go through the deck. A deep anchor locker is a plus with this type of windlass since the weight of the rode is what is what is pulling it into the locker.

A horizontal windlass usually sits higher off the deck and can be a "tripper". The gypsy is also usually exposed. The rode makes roughly a 90 degree trip around the gypsy before being pushed into the anchor locker. If your anchor locker is shallow a horizontal windlass might be a better choice.

Good luck!
 
About six months after I had my windlass installed, they came out with a combo line/chain windless which cost less then what I paid. That was a big disappointment! 15 yrs later, I'm still waiting for mine to break so I have a valid reason to replace it. [:-weepn] Be sure any windlass handles this combo so you can have plenty of chain.

Always secure your anchor rode to a cleat or such and take the load off of the windlass when at anchor. Never pull the boat by the windless. Instead drive the boat toward the anchor using the engines and draw the anchor rode in with the windlass.

Enjoy! I couldn't anchor out by myself without a windlass......
 
My current set up is 12 feet of 1/4 inch chain and 200 feet of 1/2 inch rope. Is there a specific rope or chain that will work better than others? My chain has a shackle in the middle so I guessing that it may need to be replaced. The rope is a little on the stiff side so I am worried about it not pulling itself into the locker.
 
quote:

Originally posted by 32carv

My current set up is 12 feet of 1/4 inch chain and 200 feet of 1/2 inch rope. Is there a specific rope or chain that will work better than others? My chain has a shackle in the middle so I guessing that it may need to be replaced. The rope is a little on the stiff side so I am worried about it not pulling itself into the locker.






I would go ahead and get a new anchor rode. If you want rope, you'll need to splice it directly to the chain anyway; no shackles allowed. Since the line is pretty stiff (and old, I surmise) why not just replace the whole thing?

But get the windlass FIRST, then get the type of chain that will fit in the windlass. Go with a galvanized chain.

I would advise that whatever windlass you get, make sure it has a manual override in the event of a power failure or malfunction. It should have a hand crank you can use to pull the rode in / out. Not all have this.

On the type, also consider if you want a powered down or free-fall windlass. A free fall will get your anchor to the bottom in a hurry. Powered lets the rode out fairly slowly and can be hard to know when the tackle has hit bottom. (I fish with my boat, and wish I had a free fall for faster setting when moving spots).
 
If you're going to get a new rode, you might want to consider Yale Cordage yacht brait. It has a much softer lay than 3 strand and coils in half the space. I had a fairly stiff 3 strand that was a nightmare of hockles and twists. I replaced it with yacht brait and haven't had a single problem since. Check out the Yale Cordage site.
 
Here's a shot of the windlass I mentioned above. It is the Lewmar 700, same as you are considering. It does a great job. I bought a new 200' line and 50' of chain. I'd never spliced before but I got good directions online and it actually turned out really well (took 2 tries)....my dock mates were quite impressed. The 700 handles 1/2 line and 1/4 chain. If I had your size boat I might consider moving up to the lewmar 1000 and a slightly bigger rode, but you know the type of anchoring you do. Best of luck, it will be a great addition to your boat.

IMG_2902.jpg
 
Terry,
Great picture. Interesting that is off center a bit. I have the same cleat as you and was thinking that I would have to move it. Does that stainless piece around the hole come with the windlass? Also, did you run the power from your current battery setup or put an additional battery and charger in the v-berth area?
Jim
 
I installed the Lewmar 1000 on my 350 Aft Cabin this summer. It's identical to the 700 in Terry's photo. That stainless piece is part of the windlass and covers the round hole I drilled in the deck. I centered mine after moving the cleat. To simplify wiring I installed an extra battery and charger in the forward cabin. I also purchased the wireless remote control which has worked fairly well and allows me to anchor from either upper or lower stations or work it from the bow. I use 20' of chain and 250' of line with a 35lb plow and have been very happy with it. The 700 probably would have done the job ok but I thought the 1000 was worth the extra money.
 
32carv,

My windlass is a Lewmar (was Simpson Lawrence) Horizon 600, the predecessor to the 700 shown above. It's ten years old, with more than 3,000 hours of cruising BC and SE Alaska, anchoring 2/3 of the time, with no problems. I'd probably choose the 1000 for your boat. A horizontal-axis windlass is more trouble free, especially if you don't have a lot of free-fall room in your rode locker. I had a vertical axis windlass originally, and had to replace it with a horizontal one to get the rode to lay down in the locker without jamming regularly.

Follow installation instructions with care. Locate it straight back from the roller, with the hole centered above your anchor locker if you can. If the surface on which it's mounted isn't real sturdy you might want to add a stainless steel plate or other strong material as a mounting base.

If it were me I'd get a new rode with at least 40' or more of chain spliced to the rope. 40' of chain with my 26' boat gives me considerably more comfort level when the weather kicks up - more like using an all-chain rode to help keep the pull on the anchor horizontal, rather than upward. And yet with the rope I have the advantage of springiness - best of both worlds.

As others have said, cleat off the rode after you anchor. In mild conditions (low wind, little or no waves, little or no current) there's no reason not to draw the boat toward the anchor with the windlass, in my experience. But if it's rougher, or the windlass is straining at all (you should be able to tell easily by the sound of it) use the engine.

My 600's gypsy uses 1/2" rope and 1/4" G4 (high-test) chain. Chain types have different link sizes - make sure you get the right one.

If you go with three-strand rope, New England Ropes makes the superior stuff in my experience. Splicing is not very hard to learn. I re-do mine each season, reversing both rope and chain while I'm at it. For a tool that makes splicing considerably easier than with an ordinary fid, get the "Point Hudson Phid" (small) from Brion Toss (author of Chapman's Knots, and rigging/splicing expert). See his web site:

http://www.briontoss.com/catalog/tools.html

I'd also suggest a copy of Chapman's Knots for excellent instructions on splicing as well as knots and whipping.
 
Hi Jim, just to let you know the windlass isn't mounted off centre...I think youre being confused by the position of the cleat. Like Y2K996 I moved the cleat so I could centre the windlass. I've incuded a couple more pictures taken the day I installed the windlass to give you a better idea. You will still want the cleat nearby so you can secure the rode to it when anchored (the windlasses arent really designed to take the strain of heavy pulling should a storm come up). And Y2K996 was quite right, the ss piece you referred to is part of the windlass, and right below is the large hole I was refering to when I suggested you seal the edges to prevent water getting at the core. As for the battery hookup, I ran straight back to the engine compartment and used my existing battery set up. I understand there may be hazards associated with putting batteries in the V-berth/cabin as they 'off gas' when recharging. Hope this helps!

IMG_0424.jpg


IMG_0425.jpg
 
Lewmar is good.

the key to install a windlass is too make sure your rode can feed directly into the anchor locker with enough space for the rode to coil and self store. you want it to come vertically, not at an angle rubbing on the hull side. Any thing else and you're going to spend a lot of time clearing jams.

make sure you get one that can handle chain/line rode, the line will have to be spliced in the chain, no shackle.

while you're in there, install a set of foot switches at the bow AND a remote swtich at the helm for those days where you need to control the boat while using the windlass. Since you're running wires, you may as well run them at the same time.
 
How hard is it to add the bow switchs after the fact? I have the Lewmar 1000 power-up-down model.
Niles
 
it shoudlnt' be hard, usually you have a set of relays/solenoid near the windlass and they connect right there...
 
quote:

Originally posted by 32carv

My current set up is 12 feet of 1/4 inch chain and 200 feet of 1/2 inch rope. Is there a specific rope or chain that will work better than others? My chain has a shackle in the middle so I guessing that it may need to be replaced. The rope is a little on the stiff side so I am worried about it not pulling itself into the locker.






I boat on an inland lake so I went with all chain. Best decision I've made. Anchor sets perfectly every time, and less scope is needed.

MAKE SURE you get the proper size chain. Mine called for 5/16 BBB chain. Nothing else worked very smoothly.

If you go with Chain / Rope only use a good tapered spice directly to the chain.

Good luck
 
Airbus,
Why would being on an inland lake require all chain and being on the ocean not? I was actually thinking the opposite, more rope less chain to save on some of the weight. My plan was to use 30ft of chain and 200ft of rope. Our inland lake is 60ft at it's deepest and we typically drop the anchor in 15ft to 20ft of water.
Jim
 
Back
Top